Menu
Suppliers Products
Global B2B sourcing platform
Verified suppliers and manufacturers
MadeInChina.com > Products > Security & Protection > Alarm & Security Systems > Probe, Sensor
Swipe or use the arrows to view product images.

Infrared Human Sensor PIR203s Pyroelectric Passive Infrared Sensor PIR Motion Human Detector

Price $0.15
Min Order 1000 Pieces
Availability In Stock
Shipping From Guangdong, China
Popularity 370 people viewed
Send Inquiry View Full Page
Model NO.:
PIR203S
Type:
Probe
Usage:
Anti-theft
Installation Mode:
Ceiling Mounted
Model:
PIR203s PIR Sensor
Trademark:
HW
Transport Package:
Standard Package
Specification:
6000pcs/carton
Origin:
China
Product Description
Pyroelectric passive infrared sensor
    1.  FEATURES:

High sensitivity and superior SNR(signal-to noise ratio);


High stability for temperature change;


High anti-interference ability (For example: vibration, radio frequency interference).
    1.  APPLICATIONS
Security

Luminaire

Family and other fields
    1. APPLICATIONS  RANGE

This specification describes a pyroelectric passive infraredsensor for passive infrared sensor device.
    1.  TYPE OF SENSOR

Balanced differential type (Series opposed type.)
    1. APPEALANCE AND DIMENSIONS
    1. VISUAL INSPECTION
There are not remarkable wounds,spots,rust and etc.
    1. APPEALANCE AND DIMENSIONS
TO-5 Package: see fig 1.
    1. ELECTRICAL CHARACTERISTICS( AT 25ºC )
 
ITEMCONDITIONRATING

6.1 Signal Output		Black Body temperature: 420K
Chopping Frequency: 1HZ, 0.3~ 3.5HZ △f
  • Vd=5V,Rs=47KΩ,the amplifier of Gain 72.5dB
Measurement method shown in Fig2.

>3000mVp-p

6.2 Noise Output		Chopping Frequency: 1HZ, 0.3~ 3.5HZ △f
  • Vd=5V,Rs=47KΩ,the amplifier of Gain 72.5dB
Measurement method shown in Fig2.

< 70mVp-p




6.3 Balance output		Black Body temperature: 420K
Chopping Frequency: 1HZ, 0.3~ 3.5HZ △f
  • Vd=5V,Rs=47KΩ,the amplifier of Gain 72.5dB
Measurement method shown in Fig2 and Fig3.
VA = A Element sensitivity (Vp-p)
VB = B Element sensitivity (Vp-p)


|VA-VB|/(VA+VB)
×100%≤10%

6.4 Operating Voltage		Single power supply RS=47KΩ
2~15V
6.5 Source VoltageVD=5V,RS=47KΩ0.4~1.0V
6.6 Circuit ConfigurationSee Fig.3 

6.7 Warm-up Time		After it conneted, it with the measurement amplifier for Fig.3 description that turns on the power supply beforehand, the amplification output is time until stabilizing.

Max: 25 Sec
    1. OPTICAL CHARACTERISTICS
 
 ITEM RATING
7.1 Field of View113 degrees from center of Element on Axis X.
 90 degrees from center of Element on Axis Y.
 See Fig 5
7.2Response wavelength bandFilter substrate:Silicon
Cut on wavelength:5.5±0.5μm Transmission:7~14μm ≥75%
7.3 Transmission Characteristics of filterSee Fig 6
 
    1.  ENVIRONMENTAL REQUIREMENTS
 
ITEM RATING
8.1Operating Tmeperature-30~70 ºC
8.2Storage Temperatur-40~80 ººC
8.3 Relative HumidityThe sensor shall operate without increase in Noise Output when exposed to 90 to 95% RH at 30ºC
continuously

8.4 Hermetic Seal		No bubbles visible in the 125±5ºC fluorocarbon
bath(FC-40) for 20sec
8.5 Reliability TestSpecified in Appendix1( page13~14)
 
    1. ROHS COMPLIANCE

This product conforms to RoHS regulatin.
 
    1. INSPECTION
    1. Process inspection
100% inspection: Item 6.1 to 6.3 and 6.5 among the electric performances of item 6.
    1. OUTGOING INSPECTION
Based on statistical sampling inspection method every manufacture lot is inspected for the electrical characteristics item 6.1to 6.3 ,6.5 of the Item 6,and item 5.1 and 5.3 of the appearance of item 5.
    1.  PACKING
The packaging is solid and there isn't breakage
    1. PROCESS ATFAILURE
In case of finding of failure incoming or process inspection after receipt of products, Both sides negotiate to deal with the failure
    1. PRODUCTION GROUND
China
    1. REVISION
Any revision of this specification should be made in writing by discussion.











  • Similar Products
Full Page Contact Supplier
↑