Audited Supplier
Drone & WiFi Jammer Power Amplifier
Wireless
GPS&2g/3G/4G/5g Cellphone
5.8g 2.4G GPS GSM 3G 4G 5g
CE, ISO
New
HS-D100-20-6000
1.5dB
SMA-Kfd
20-6000MHz
N-F
Uav Defense
481dBm
24V-30V
HiSea
Neutral Packing
Guangdong, China
Product Description
Item | Parameter | Remarks | ||
Operating Voltage | 28V | 24-30V | ||
Conversion efficiency | ≥42% | @100W typical | ||
Controllable output power | 10W~100W | Software set power level | ||
ALC power adjustment range | ≥30 dB | Voltage Controlled Attenuation | ||
Gain | 50±1.0 dB | |||
In-band fluctuation | ≤2.5 dB | peak-to-peak | ||
spurious emission | ≤-15dBm/1MHz | Measured when the center frequency plus CW signal to the maximum output power | ||
out of work band | 9KHz~1GHz | No higher than normal noise floor clutter | ||
1G~12.75GHz | ||||
Maximum allowable input power | ≥+10 dBm | Lasts 1min without damage | ||
Input VSWR | ≤1.35 dBm | Add +28V, standard network output -10dBm | ||
Output VSWR | ≤1.30 dBm | No power, standard network output -10dBm | ||
≤1.35 dBm | Power On, Dual Directional Coupler Test | |||
High and low temperature test | Working ambient temperature (ºC) | -10~+65 | Low temperature can start, monitoring works normally | |
Gain Stability | ±1.5 dBm @-40ºC~+65ºC | |||
power stability | ±1 dBm @-40ºC~+65ºC | |||
Power Requirements | ≥8A @+28Vdc; | CW output 100W | ||
Power supply interface, monitoring interface RS485 | 7W2 | Male | ||
RF output connector | N-F connector | |||
LCD liquid crystal display | Display frequency, power, switch status | |||
with 3 LED lights | POWER: Power indication; RUN: Running indication; ALARM: Alarm indication; | |||
Built-in cooling fan | Modules can be run separately | |||
Physical dimension | 155 x 125 x 60mm | |||
Weight | 1.6Kg | |||
Appearance (how to use) | Black integrated module with fan (single or portable use) | |||
Monitoring | Function Description | Remarks | |
Amplifier part setting parameters | Amplifier switch | Turn the amplifier on or off | |
Alarm switch | Enable and disable the alarm function | ||
Downlink Power Control | The maximum output power of the power amplifier can be set, the adjustment range is ≥20dB, and the high, medium and low power levels can be set | ||
Amplifier over temperature alarm | The high temperature power amplifier shutdown threshold can be set, the power amplifier temperature exceeds 85 degrees, it will automatically shut down; 65 degrees will automatically restore | ||
Amplifier overpower alarm | The actual power value is 2dB higher than the downlink ALC start control threshold and close | ||
Power amplifier standing wave alarm | When the standing wave detection of the power amplifier is greater than 4, the power amplifier is automatically turned off | ||
Amplifier overcurrent alarm | When the detection current of the power amplifier exceeds 12A, the power amplifier is automatically turned off | ||
Amplifier under-power alarm | When the power amplifier detection power is less than 37dBm, an under-power alarm is displayed | ||
Amplifier overvoltage alarm | When the power amplifier voltage exceeds 32V, the power amplifier will automatically shut down | ||
Amplifier switch status | If the power amplifier is set to "OFF", the query should be the state of the power amplifier off; otherwise, the state of the power amplifier will be turned on. | ||
Downstream output power level value | Detect power amplifier output power value, detection range (Pomax+2, Pomax-20) | Detection accuracy:Pout±1dB | |
Downward standing wave ratio | The standing wave is normally 1.2, when the load is mismatched, the query value is 4.0 | ||
Temperature query | Detect the internal temperature of the module, detection range: -40ºC~+100ºC | detection error:±3ºC | |
ALC value query | The displayed value is equal to the actual set ALC value | ||
Voltage detection | Detection module working voltage | ||
Current Detection | Detection module operating current | ||
Signal generator settings | Frequency setting mode 1 | Any single frequency point setting within the range | The frequency setting accuracy is 1M, the maximum frequency bandwidth is 500M, and the maximum is 6G |
Frequency setting mode 2 | Set the broadband frequency sweep mode, parameters such as frequency, interval, and step can be set | ||
Frequency setting mode 3 | Set any 4 sub-frequency segments within the bandwidth, and a single sub-segment needs to be incremented | ||
module communication | RS485 | ||
Interface definition | +:28V,-: GND; control bit 1:485A,2:485B | ||
OEM customized service:
Frequency, band, jamming distance: can be customized.
Silkscreen OEM service can be offered.
Any combinations, and customizations are possible, just send us your inquiry and we will give you our recommendation.
Silkscreen OEM service can be offered.
Any combinations, and customizations are possible, just send us your inquiry and we will give you our recommendation.
Q1. Could I get a sample before bulk order?
Yes, We offer samples for all models, but the sample costs, shipping and taxes paid by the buyer.
Q2.Payment Method
T/T, Western Union, Paypal, and Credit Card are available, *Other methods please Contact us with more details.
Q3.Delivery Date&Lead Time
Small equipment that is in stock is expected to be shipped within 2-5 days after payment is received. If you need customized equipment for large projects, please contact customer service ~ we will deliver it to you as quickly as possible and with stable quality control.
Q4. Can I customize frequencies?
Yes, we can customize 2G/3G/4G/5G/LoJack 173MHz, VHF, UHF, Walkie-talkie, interphone, 433MHz,315MHz, 868MHz, 450MHz, iDEN,CDMA,GSM, GPRS, DCS, PCS, AWS, WCDMA, UMTS,3G,4G, LTE 700, LTE 800, LTE 2300, LTE 2600, GPS L1, GPS L2, Galileo, Compass, Glonass,WIFI, Bluetooth, WIMAX, UAV, Drone, 5.8G, etc.
Q5. What should I do if I don't know about frequency in my country?
Please feel free to Contact us with your inquiry, we will find the frequency you need and address your problems.
