Audited Supplier
MK-EP2366
Flexible
Flow Production Line
Comprehensive
Product Line
Intelligent Manufacturing
ISO, CE
New
Automatic
1 Year
1 Year
Markevina or OEM
Wooden Case
Customized
China
Product Description
Air Conditioner Production Line, Home Appliance Production Line Customized
| 1. Production line technical requirements: | |||
| 1. Suitable products: air conditioners. | |||
| 2. Design single-shift output: The production cycle is 12~40 seconds/set. | |||
| 3. Power supply for line body conductive system: single-phase 220V, 50HZ, with leakage protection. | |||
| 4. The line body supplies compressed air: 0.6-0.8Mpa. ; The end of each line body is equipped with air source treatment triplex and blowdown valve. | |||
| 5. Power supply: 220V, 50HZ, power consumption: 15kw. | |||
| 6. See the floor plan of the sub-machine line for the station layout. | |||
| 2. Production line installation address: | |||
| 3. The specific configuration and quotation are as follows: | |||
| No | Specifications and Requirements | unit | Qty |
| 1 | Partial belt conveyor line: | set | 1 |
| Basic size: L13300×W650mm×H800mm, can be adjusted up and down by 50mm, 3 pieces | meter | 40 | |
| Basic size: L11500×W650mm×H800mm, can be adjusted up and down by 50mm, 2 pieces | meter | 23 | |
| Line body aluminum profile: special aluminum profile 35X130, | |||
| (3) | Belt width: 650mm, 10 meters section of power, thickness 3mm, wear-resistant, anti-aging, anti-static color green color number seamless interface | ||
| The line body is made of high-quality aluminum alloy edge protection (130*35 type), and the support roller is a ф38mm steel roller with a spacing of 800mm. | |||
| (5) | The line body bracket is made of 40mm*40mm*2.5mm square tube, the bracket spacing is 2 meters, the support plate is folded from 2mm steel plate, the support plate is the same height as the edge protection, and the belt is 3mm higher than the edge protection. The distance between the joints of the two belt lines is less than 5mm. The belt line surface is required to be flat and free of ups and downs. | ||
| Wire trough and socket: There is a wire trough under the wire body, which is made of A3 steel plate, and the surface is sprayed with plastic. Each station is equipped with a 2+3 hole wall socket; the distance between the racks is 1.5m, and the foot cup M16 adjustment screw; | set | 1 | |
| Pallet: 1.2mm steel plate, galvanized surface; supporting roller: ¢38 supporting roller, 1.2 pcs/m; guide roller: ¢60 seamless steel pipe, screw fine-tuning, the height of the supporting plate belt is required to be 5mm higher than the height of the guide rail profile. | |||
| Gas line: The line body is installed with Φ20 galvanized pipes, 12 5*8 quick connectors, triple air source, and the air circuit is installed above the production line. | set | 1 | |
| Install two 220V/10A two-position universal sockets at the appropriate parts under each line body (on-site installation according to Party A's requirements). | |||
| Each belt line is equipped with an emergency stop switch, which has the function of stopping in time. | |||
| Wire carrying capacity: ≥50kg/set. | |||
| Lamp pole: 80*40mm square steel pipe is used, sprayed with plastic, the installation distance is 4m, and the distance between the lamp post and the line body is 800mm. | set | 1 | |
| Lamp hoisting: use 40*60mm square steel pipe, | set | 1 | |
| Drive device: Taiwan Yongkun 1.5KW geared motor | set | 1 | |
| Inverter: Delta 1.5KW inverter, line speed 1.2m-6m/min adjustable, | set | 1 | |
| 2 | Packaging line body | ||
| 2.1. Power roller conveyor | |||
| 2.1.1 Wire body specification: length 2×width 0.66×height 0.7 (m) | set | 5 | |
| (Note: The length of the conveyor is subject to the design) | |||
| 2.1.2 The drive adopts a three-phase geared motor, equipped with sprockets and chains | |||
| 2.1.31 The guide rail of the line body adopts 35×130 high-quality aluminum profiles, and the surface is oxidized | |||
| 2.1.4 The roller adopts Ф60×500 stainless steel power roller with a spacing of 150. | |||
| 2.1.5 The drum surface is 10mm higher than the wire body | |||
| 2.1.6 Line body bracket: aluminum profile bracket with adjustable foot cup M16mm | |||
| 3 | 1 chain line for electric tooling | set | 1 |
| 4 | Light stand: | meter | 60 |
| 5 | Pillow packaging machine: | set | 1 |
| 6 | Nailing and sealing machine: | set | 1 |
| 7 | Packer: | set | 1 |
| 8 | Electrical control: | set | 1 |
