Audited Supplier
Sanbar 61
Technical/Sample/Quality
Technical/Sample/Quality
Seamless
Hot Rolled
Alloy Steel
Seamless
SHUNFU
Strip
China
Product Description
Sanbar 61 Hollow Drill Steel
Sanbar 61 is a high strength silicon steel with good toughness and impact resistance in the as-rolled condition.Chemical composition (nominal)
| Chemical composition (nominal) % | |||||||
| C | Si | Mn | P | S | Cr | Ni | Mo |
| 0.41 | 1.5 | 0.9 | ≤0.025 | ≤0.020 | 0.7 | 0.5 | 0.2 |
Applications
Sanbar® 61 is used for tapered rods, pilot rods and integral drill steels.Forms of supply
Hollow drill steel is supplied as hollow, hot-rolled, round or hexagon bar. The ends are trimmed square to within 0.15 mm (0.006 in.) maximum.Surface condition and protection
Both the outer and inner surfaces are free from harmful slag marks, cracks and scratches. The maximum depth of defects is 0.20 mm (0.008 in.) on the outer surface and 0.15 mm (0.006 in.) on the inner surface.The outer surface can be supplied dry or oiled for protection against corrosion during transportation. The flushing holes are normally sealed with plastic caps.
Straightness
Maximum deviation is 1 mm per 1000 mm (0.04 in. per 39.4 in.).Fixed lengths
Fixed lengths can be supplied upon request. The length tolerance for fixed lengths are:| Lengths, mm (in.) | Tolerance, mm (in.) |
| ≤ 3375 (132.87) | +/- 2 (0.0787) |
| 3376-5750 (132.91-226.38) | +/- 3 (0.1181) |
| > 5750 (226.38) | +/- 4 (0.1575) |
Mechanical properties
| As-delivered condition, typical values Proof strength | Tensile strength | Hardness |
| Rp0.2 | Rm | HRC |
| MPa (ksi) | MPa (ksi) | |
| 820 (119) | 1350 (196) | 38-44 |
Decarburization
The maximum permissible decarburization depth is 0.30 mm (0.012 in.) on the outer surface and 0.10 mm (0.004 in.) on the inner surface.Machining
Machining may require prior annealing.Forging
Induction heating to 1000-1100°C (1830- 2010°F), 10-20 seconds, cooling in air. Forging range 1100-850°C (2010-560°F).Heat treatment
Annealing (induction heating) 730-780°C (1350-1440°F), cooling in air.Read more about heat treatment of Sanbar® 61 under Fabrication.
Normalizing (induction heating)
1000-1050°C (1830-1920°F), cooling in air. Shank end hardening (case hardening). Read more about shank end hardening of Sanbar® 61 under Fabrication.
Hardening: Induction heating to 900-1000°C (1650-1830°F), 2-5 seconds.
Quenching in water or oil.
Tempering
Recommended surface hardness 55-60 HRC, temperature appr. 150-250°C (300-480°F).
Forging
Sanbar® 61 requires rapid heating to the forging temperature and, above all, the soaking time at full temperature should be as short as possible. This will minimize grain growth and decarburization, both of which drastically impair the fatigue strength.The design of the shank and the forging of the collar are very important to the properties and performance of the drill rod. Abrupt changes in cross-section and forging defects cause stress concentrations that can severely diminish the performance of the rod and give rise to fracture. It is therefore vital that the radius between the collar and the rod is generous and defects such as laps, folds and cracks are to be avoided.
Heat the rod end locally to the correct forging temperature. Forge within the temperature range specified for Sanbar® 61, and terminate at the lower end of the temperature range. This will restrict grain growth. Forge the collar using a mandrel in the flushing hole, so that the flushing tube will not close up during forging.
Shank end hardening
The shank must be hardened after forging and machining to obtain the strength necessary for robust service. Sanbar® 61 has been developed primarily for surface induction hardening. A normalizing process is recommended in order to eliminate prior transition zones and create optimum mechanical properties. This process will decrease the grain size and result in a microstructure with high strength and good toughness. Normalize within the temperature range specified for Sanbar® 61. Recommended hardness range: 38-44 HRC. The heated zone should overlap the previously heated zone by about 25 mm.After the above treatment, surface induction harden the shank by heating and quenching according to the recommendations above. Temper for 0.5 hour in the range of 150-250°C (300-480°F) to obtain a hardness of 55-60 HRC.
Brazing
The minimum hardness value in the transition zone resulting from the brazing operation should be as high as possible. It is very important to avoid interaction between transitions zones and geometrical notches.Shot peening
Shot peening of an adequate intensity and coverage is recommended. It improves fatigue strength due to:Introduced compressive stresses
Increased hardness
Smoother surface defects
