Audited Supplier
Sidewall conveyor belt can be used for horizontal, sloping or vertical conveyance and it is one of the most effective ways of elevating materials in a confined space. The economic goal can be achieved by single belt operation and wide range materials can be handled in cases of limited space and strict requirements of no transfer point, low maintenance and big capacity.
Sidewall conveyor belt can be used for horizontal, sloping or vertical conveyance and it is one of the most effective ways of elevating materials in a confined space. The economic goal can be achieved by single belt operation and wide range materials can be handled in cases of limited space and strict requirements of no transfer point, low maintenance and big capacity.
The EP conveyor belt consisting of 1-6 EP fabric plies, EP rubber conveyor belt has the same merit as Nylon conveyor belt. Its tensile body is made of warp polyester and weft-knitted canvas. Its performance is characterized by low elongation in the warp direction and excellent groove formation in the weft direction. The wet strength does not decrease, no mildew occurs, the initial modulus of the polyester is high, and a lower safety factor can be taken. It is suitable for conveying materials under medium and long-distance and high load and high-speed conditions.
It is based on the following main components:
- Cross-stabilized Base Belts
(2) Sidewalls
(3) Cleats - Sidewall Conveyor belt has been designed with two corrugated sidewalls and cleats molded to cross-rigid base belt which can carry heavy product loads up to the inclined angle of 75°. This belt is popular where space is at a premium and steep incline angles are desired.
| Belt width (mm) | Sidewall height (mm) | Cleat height (mm) | Effective belt width (mm) |
| 400 | 60 | - | |
| 80 | 70 | ||
| 100 | 90 | ||
| 120 | 100 | ||
| 500 | 60 | 250 | |
| 80 | 70 | ||
| 100 | 90 | ||
| 120 | 110 | ||
| 160 | 140 | ||
| 650 | 60 | 250, 300, 350 | |
| 80 | 70 | ||
| 100 | 90 | ||
| 120 | 110 | ||
| 160 | 140 | ||
| 200 | 180 | ||
| 800 | 60 | 350, 410, 460 | |
| 80 | 70 | ||
| 100 | 90 | ||
| 120 | 110 | ||
| 160 | 140 | ||
| 200 | 180 | ||
| 240 | 220 | ||
| 1000 | 60 | 460, 550, 640, 690, | |
| 80 | 70 | ||
| 100 | 90 | ||
| 120 | 110 | ||
| 160 | 140 | ||
| 200 | 180 | ||
| 240 | 220 | ||
| 300 | 270 | ||
| 1200 | 60 | 460, 550, 640, 690 | |
| 80 | 70 | ||
| 100 | 90 | ||
| 120 | 110 | ||
| 160 | 140 | ||
| 200 | 180 | ||
| 240 | 220 | ||
| 300 | 270 |
Manufacturing standards
GB/T 7984
DIN 22102
JISK 6322
AS 1332-2000
SANS 1173:2005
BS 490
| Standards | Cover Rubber | Adhesion | ||||
| Tensile Strength | Elongation at break | Abrasion | Cover to Ply | Cover to Ply | Ply to Ply | |
| DIN 22102 | Mpa | % | mm3 | N/mm | N/mm (>1.5mm) | N/mm |
| DIN 22102-Z | 15 | 350 | 250 | 3.5 | 4.5 | 5 |
| DIN 22102-W | 18 | 400 | 90 | 3.5 | 4.5 | 5 |
| DIN 22102-Y | 20 | 400 | 150 | 3.5 | 4.5 | 5 |
| DIN 22102-X | 25 | 450 | 120 | 3.5 | 4.5 | 5 |
| Standards | Cover Rubber | Adhesion | ||||
| Tensile Strength | Elongation at break | Abrasion | Cover to Ply | Cover to Ply | Ply to Ply | |
| RMA | Mpa | % | mm3 | N/mm (≤1.6mm) | N/mm (>1.6mm) | N/mm |
| RMA-I | 17 | 400 | 200 | 3 | 4.4 | 4 |
| RMA-II | 14 | 400 | 250 | 3 | 4.4 | 4 |
| Standards | Cover Rubber | Adhesion | ||||
| Tensile Strength | Elongation at break | Abrasion | Cover to Ply | Cover to Ply | Ply to Ply | |
| AS 1332 | Mpa | % | mm3 | N/mm (≤1.9mm) | N/mm (>1.9mm) | N/mm |
| AS 1332-N17 | 17 | 400 | 200 | 4 | 4.8 | 6 |
| AS 1332-M24 | 24 | 450 | 125 | 4 | 4.8 | 6 |
| Carcass | fabric type | Strength per ply (N/mm) | Thickness per ply (mm) | Cover Thickness (mm) | No.of Ply | Belt Width (mm) | Length per Roll (m/Roll) | |
| Top Cover | Bottom Cover | |||||||
| NN | NN100 | 100 | 0.70 | 3 3 3.2 4 4.5 4.8 6 6 6.4 7.9 8 9.5 | 1.5 3 1.6 2 4.5 1.6 2 6 3.2 3.2 4 3.2 | 2-10 | 300-12000 | 20-100 |
| NN125 | 125 | 0.70 | ||||||
| NN150 | 150 | 0.75 | ||||||
| NN200 | 200 | 0.90 | ||||||
| NN250 | 250 | 1.15 | ||||||
| NN300 | 300 | 1.25 | ||||||
| NN400 | 400 | 1.50 | ||||||
| EP | EP100 | 100 | 0.75 | 2-8 | ||||
| EP125 | 125 | 0.75 | ||||||
| EP150 | 150 | 0.85 | ||||||
| EP175 | 175 | 0.85 | ||||||
| EP200 | 200 | 1.00 | ||||||
| EP250 | 250 | 1.20 | ||||||
| EP300 | 300 | 1.35 | ||||||
| EP350 | 350 | 1.50 | ||||||
| EP400 | 400 | 1.65 | ||||||
| EP500 | 500 | 2.00 | ||||||
| CC | CC56 | 56 | 1.10 | 3-12 | ||||
Hebei TRX Rubber Products Co., Ltd is a leading professional manufacturer of conveyor belts & conveyor accessories in China. The main workshops cover 20,000 square meters in the total 60,000 square meters of the plant. The applied technology and equipment in the advanced production lines are state of the art in the industry. The sales headquarters is located in the capital of China, Beijing with branches in domestic and abroad.
It specializes in following three series: 1) Heavy-duty Conveyor Belt, including universal EP/NN and CC Belt, Chevron Belt, Oil Resistant Belt, Abrasion Resistant Belt, Heat Resistant Belt, Fire Resistant Belt, Chemical Resistant Belt, Sidewall Belt, Flat Transmission Belts, 2) Rubber Sheets, including SBR, NBR, NR, CR, EDPM, Rubber With Insertion 3) Conveyor accessories. These three series of products conform to RMA, DIN, ASTM and ISO specifications.
Its products, honored with "The most Advanced level of Products" by the Committee of Science and Technology, have been widely used in mining and quarrying, power stations, steel plants, bulk cargo terminals, cement industry, and other material handling fields. With great success in domestic market, it has been focusing on global market with several hundreds of foreign valued customers in Asia, South America, North America, Africa and Europe.
The company mission:
1.Supply one-stop outstanding service to global customers.
2. Engage in complete solutions with conveyor belting and power transmission belting.
3. Persist in technology improvement and quality control in the whole process of production and service.
