Audited Supplier
zm6125
220V/50Hz
Yes
for Colleges, Universities, Technical Schools
220kgs
3cbm
3 Years
ShouldShine
Plywood
aluminum
China
Product Description
ZM6125 Computerized Air Conditioning Trainer
I Introduction
This trainer is designed for studying of the thermodynamic transformations the air undergoes when crossing the various stages of a modem air conditioning unit that serves a room where temperature and relative humidity must be checked. Measuring air temperature and humidity in different points enables to analyze air cooling, heating, humidification, dehumidification. Moreover some simulators of room and outdoor temperature and of room humidity are included to verify the logic of control system in all the conditions that can occur in an air handling unit. The equipment is also provided with sensible and latent heat generators installed in the test room that can be used to vary the thermal load in the same room and to check the response of the control system. The controller includes the functions of calibration and control, it enables students to energy to enter the points of control system, such as set points, measurement values, etc… via a PC (demand), so that any alarm along the circuit can be detected and a different management of the system can be programmed.
Supply software which can monitor voltage, current, frequency, power, power factor,
pressure, flow, etc, they can be displayed on PC in real time, and can print report.
II Training Program
Using the psychrometric chart to study the transformations the air undergoes in the different sections of and air handing unit, that is: sensible heating, steam humidification, cooling and dehumidification.
Assessing the heat balances corresponding to the different sections of the air handing unit
Analyzing the operation of temperature and humidity controllers for AHU
Direct and reverse acting proportional control
ON/OFF step control
Dampers temperature control
Checking the behaviour of control system versus thermal loads
Supplied with:
English General refrigeration manual
English Theoretical-experimental handbook
Company Information
We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today's and tomorrow's careers.
Service
We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.
Certificate
Our products takes ISO9001 product management system.
I Introduction
This trainer is designed for studying of the thermodynamic transformations the air undergoes when crossing the various stages of a modem air conditioning unit that serves a room where temperature and relative humidity must be checked. Measuring air temperature and humidity in different points enables to analyze air cooling, heating, humidification, dehumidification. Moreover some simulators of room and outdoor temperature and of room humidity are included to verify the logic of control system in all the conditions that can occur in an air handling unit. The equipment is also provided with sensible and latent heat generators installed in the test room that can be used to vary the thermal load in the same room and to check the response of the control system. The controller includes the functions of calibration and control, it enables students to energy to enter the points of control system, such as set points, measurement values, etc… via a PC (demand), so that any alarm along the circuit can be detected and a different management of the system can be programmed.
Supply software which can monitor voltage, current, frequency, power, power factor,
pressure, flow, etc, they can be displayed on PC in real time, and can print report.
II Training Program
Using the psychrometric chart to study the transformations the air undergoes in the different sections of and air handing unit, that is: sensible heating, steam humidification, cooling and dehumidification.
Assessing the heat balances corresponding to the different sections of the air handing unit
Analyzing the operation of temperature and humidity controllers for AHU
Direct and reverse acting proportional control
ON/OFF step control
Dampers temperature control
Checking the behaviour of control system versus thermal loads
Supplied with:
English General refrigeration manual
English Theoretical-experimental handbook
Company Information
We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today's and tomorrow's careers.
Service
We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.
Certificate
Our products takes ISO9001 product management system.
