Audited Supplier
D120-50X4
>150m
>400 L/min
Motor
Multistage Pump
Low Pressure Pump
Single Suction Pump
Horizontal Pump
Horizontal Split Pumps
Since Irrigation Centrifugal Pumps
Closed
Pump, Pumps
Changsha Swan
Wuxi Pump Works
Below 0.6MPa
0-80 Celsius
Accept
LEO
Export Plywood Case
China
8413709990
Product Description
Introduction
D type pumps are single suction multistage segmental centrifugal pumps which adopt energy efficient hydraulic model,with wide performance range,high efficiency,reasonable structure,safe and steady operation,low noise,long life performance and easy installation and maintenance.
Application
D type pump apply to mining,factory and city water supply and drain,and are used for transporting clear water without solid particles, abrader and suspended substance or other liquids that their physical and chemical properties are similar to clear water
Performance Parameters Table
Product Attribute
Structural characteristics
The pump series is installed horizontally,the inlet is horizontal and the outlet is upward,they can be changed as required.the pump consists of pump body,rotor,balanced construction,bearing and seal
Pump body:suction casing,stage casing,discharge casing and diffuser are linked by bolts to form a working house
Rotor:it consists of shaft,impeller,shaft sleeve,balance disk etc,the spare parts of shaft are rolled into one by straight supported by bearing at both ends keys and sleeve nuts,the rotor is in pump casing
Balanced construction:it consists of gimbals,balancing sleeve,balanced pipeline
Parts of bearing:they consist of shaft box,bearing and bearing cover.except 600-80,800-80 type pump adopt sliding bearing and oil lubrication,other pumps adopt rolling bearing and grease lubrication
Sealing parts usually adopt packing seal,mechanical seal as well
Drive: pump is driven directly by motor through flexible coupling,viewed from the motor end, the rotating direction of pump is clockwise.
Ordering instructions
The necessary parameters: Pump type or capacity, head at required operating point,suction pressure,density,temperature,viscosity and causticity of pumped medium etc,type of shaft sealing,motor power,voltage,insulation class,level of protection,cooling system.
FAQ
D type pumps are single suction multistage segmental centrifugal pumps which adopt energy efficient hydraulic model,with wide performance range,high efficiency,reasonable structure,safe and steady operation,low noise,long life performance and easy installation and maintenance.
Application
D type pump apply to mining,factory and city water supply and drain,and are used for transporting clear water without solid particles, abrader and suspended substance or other liquids that their physical and chemical properties are similar to clear water
Performance Parameters Table
| Model | Flow(m³/h) | Head(m) | Pump efficiency(%) | Shaft power (kW) | Speed(rpm) | Impeller outer diameter(mm) | Stage |
| D120-50X4 | 120 | 200 | 73.3 | 89.22 | 2950 | 213 | 4 |
Product Attribute
| Attribute | Attribute | Attribute value |
| Performance | Speed | 2950 |
| Material | Impeller | HT250 |
| Pump shaft | 40Cr | |
| Bearing | SKF | |
| Pump casing | HT250 | |
| Working conditions | Medium temperatur(ºC) | Below 80ºC |
| Installation | Inlet diameter(mm) | DN125 |
| Outlet diameter(mm) | DN125 | |
| Direction of rotation | Clockwise | |
| Entrance orientation | Side entry | |
| Exit orientation | Vertical up | |
| Instructions | Low pressure male bottom | |
| Motor | Number of motor phases | 3 |
| Protection class | IP54 | |
| Insulation class | F | |
| Motor Power(kW) | 110 | |
| Motor model | YE3-315S-2 | |
| Power frequency(Hz) | 50 | |
| Rated voltage(V) | 380 | |
| Seal | Sealed form | Machinery Seal |
Structural characteristics
The pump series is installed horizontally,the inlet is horizontal and the outlet is upward,they can be changed as required.the pump consists of pump body,rotor,balanced construction,bearing and seal
Pump body:suction casing,stage casing,discharge casing and diffuser are linked by bolts to form a working house
Rotor:it consists of shaft,impeller,shaft sleeve,balance disk etc,the spare parts of shaft are rolled into one by straight supported by bearing at both ends keys and sleeve nuts,the rotor is in pump casing
Balanced construction:it consists of gimbals,balancing sleeve,balanced pipeline
Parts of bearing:they consist of shaft box,bearing and bearing cover.except 600-80,800-80 type pump adopt sliding bearing and oil lubrication,other pumps adopt rolling bearing and grease lubrication
Sealing parts usually adopt packing seal,mechanical seal as well
Drive: pump is driven directly by motor through flexible coupling,viewed from the motor end, the rotating direction of pump is clockwise.
Ordering instructions
The necessary parameters: Pump type or capacity, head at required operating point,suction pressure,density,temperature,viscosity and causticity of pumped medium etc,type of shaft sealing,motor power,voltage,insulation class,level of protection,cooling system.
FAQ
| 1. Q:Are you a manufacturer or trading company |
| A:We are a manufacturer that specializes in industrial pump for 60 years |
| 2. Q:What payment term do you prefer? |
| A:Normally we take payment term 30% T/T in advance,70% paid before shipment, we can also accept L/C at sight. |
| 3. Q:What about the package? |
| A:Standard export plywood case |
| 4. Q:How long is the warranty? |
| A: Eighteen (18) months after delivery, twelve (12) Months from the date of commissioning, whichever comes earlier |
| 5. Q:Is it acceptable to make customer's own brand? |
| A: Sure, we can do OEM & ODM |
| 6. Q:How many days does it take for manufacturing? |
| A: It depends on order quantity and pump types. Normally it takes 20-120 days |
