Audited Supplier
GW900
Household Appliances, Garden Supplies, Decoration, Commodity, Auto Part, Electronic, Stationery
Air Cooling
Semi-Automatic
Low Frequency
AC
Handheld
Electric
OBOR
Aluminium Packing Box
GW600, GW800, GW900, GW1600
Taian, Shandong, China
8515809090
Product Description
Geomembrane Welding Machine-GW900
1.Product description
GW900 geomembrane welding machine adopts advanced hot wedge structure. With its high power, high speed and pressure, it welds 1.0mm-3.0mm thickness hot melting materials such as HDPE,LDPE,PVC,EVA,ECB,PP and other hot melt materials. This machine is specially designed for water conservancy, aquaculture, landfills, chemical mining, sewage treatment, roof constructions and other waterproofing projects.
2.Technical parameter
3.Main Components
4. Operating regulations
1.)Use with grounded 3-cord mains cable and 3-hole socker with capacity not less than 10A (socket corresponds with welder plug,phase L connected to live wire ,N to zero line ,phase to grounded protection liner),confirm that external lines have been well connected .Check that power is on off state and regulate temperature control potentiometer and speed control potentiometer to 0 position ,press lever handle down to disengage pressure roller ,then insert the plug .
2). Turn on the power and select certain temperature and speed, take several narrow materials for try welding. Temperature selection may be different for the same material at different ambient temperature and material thickness. To determine the best welding effect, adjust the speed to approximately 2m/min, and then fine increase it from low to high temperature (approximately 250ºC-350ºC).
3). Flatly and straightly trim the weld edges and frontage faced, with lower left and upper right overlapped. The overlap width is 100mm.
4). After temperature and speed have been determined, insert material to be welded between the two pressure rollers, make machine body parallel with edges of base materials and engage press lever handle for proper motion. Generally, only observation of deviation between welding mark and base materials is needed for operator, and timely make correction on small degree.
5). When welding will be ended, timely press lever handle to disengage upper and lower pressure roller to prevent rubber wheel damage for long duration.
6). Excessive temperature high and low may occur because of thermal inertia. On this condition, temperature deviation may be compensated by speed regulation on a small degree.
5.Packing
Aluminium packing box
Box Size: 500mm×370mm×410mm
Weight: 18kg
6.Application
Shandong OBOR New Materials Co., Ltd
Taian. Shandong. China
1.Product description
GW900 geomembrane welding machine adopts advanced hot wedge structure. With its high power, high speed and pressure, it welds 1.0mm-3.0mm thickness hot melting materials such as HDPE,LDPE,PVC,EVA,ECB,PP and other hot melt materials. This machine is specially designed for water conservancy, aquaculture, landfills, chemical mining, sewage treatment, roof constructions and other waterproofing projects.
2.Technical parameter
| Brand & Type | GW900 Geomembrane Welding Machine |
| Certificate | CE \ RoHS |
| Voltage | 220V/110V |
| Power | 1600-2000W |
| Frequency | 50 HZ / 60HZ |
| Welding Speed | 0.5-5m/min |
| Heating temperature | 20-450ºC |
| Thickness of material | 1.0mm--3.0mm |
| Overlap width | 12cm |
| Wedling width | 16mm×2, interior cavity 18mm |
| Seam strength | ≥85% base material(tensile resistant in shear direction) |
| Weight | 13kg |
| Insulation class | Class II |
| Usage | China geomenbrane wedge wlder |
| Plug Standard | Euro Plug/ U.S. Plug/Chinese Plug |
4. Operating regulations
1.)Use with grounded 3-cord mains cable and 3-hole socker with capacity not less than 10A (socket corresponds with welder plug,phase L connected to live wire ,N to zero line ,phase to grounded protection liner),confirm that external lines have been well connected .Check that power is on off state and regulate temperature control potentiometer and speed control potentiometer to 0 position ,press lever handle down to disengage pressure roller ,then insert the plug .
2). Turn on the power and select certain temperature and speed, take several narrow materials for try welding. Temperature selection may be different for the same material at different ambient temperature and material thickness. To determine the best welding effect, adjust the speed to approximately 2m/min, and then fine increase it from low to high temperature (approximately 250ºC-350ºC).
3). Flatly and straightly trim the weld edges and frontage faced, with lower left and upper right overlapped. The overlap width is 100mm.
4). After temperature and speed have been determined, insert material to be welded between the two pressure rollers, make machine body parallel with edges of base materials and engage press lever handle for proper motion. Generally, only observation of deviation between welding mark and base materials is needed for operator, and timely make correction on small degree.
5). When welding will be ended, timely press lever handle to disengage upper and lower pressure roller to prevent rubber wheel damage for long duration.
6). Excessive temperature high and low may occur because of thermal inertia. On this condition, temperature deviation may be compensated by speed regulation on a small degree.
5.Packing
Aluminium packing box
Box Size: 500mm×370mm×410mm
Weight: 18kg
6.Application
Shandong OBOR New Materials Co., Ltd
Taian. Shandong. China
