Audited Supplier
Pet is an opalescent or light yellow highly crystalline polymer with smooth and glossy surface. It has good creep resistance, fatigue resistance, wear resistance and dimensional stability, small wear and high hardness. It has the largest toughness in thermoplastic plastics: good electrical insulation performance, little influence by temperature, but poor corona resistance. It is non-toxic, weather resistant, chemical resistant, stable, low water absorption, weak acid and organic solvent resistance, but not resistant to hot water immersion and alkali.
PET resin has high glass transition temperature, slow crystallization rate, long molding cycle, large molding shrinkage, poor dimensional stability, brittle molding and low heat resistance.
| Item | Unit | CZ-302 | CZ-302L | CZ-302A | CZ-318 | CZ-328 | CZ-328A | CZ-328H | CZ-333 |
| IV | DL/G | 0.8+/-0.015 | 0.78+/-0.015 | 0.8+/-0.015 | 0.83+/-0.015 | 0.875+/-0.015 | 0.87+/-0.015 | 0.89+/-0.015 | 0.8+/-0.015 |
| Cristallinity | % | 55+/-5 | 55+/-5 | 55+/-5 | 55+/-5 | 55+/-5 | 55+/-5 | 55+/-5 | 55+/-5 |
| Color | L- | ≥82 | ≥82 | ≥72 | ≥82 | ≥82 | ≥72 | ≥82 | ≥82 |
| B- | ≤1.0 | ≤1.0 | ≤0.0 | ≤1.0 | ≤1.0 | ≤0.0 | ≤1.0 | ≤1.0 | |
| COOH | Mmol/kg | ≤30 | ≤30 | ≤30 | ≤30 | ≤30 | ≤30 | ≤30 | ≤30 |
| AA | ppm Ug/g | ≤1.0 | ≤1.0 | ≤1.0 | ≤1.0 | ≤1.0 | ≤1.0 | ≤1.0 | ≤1.0 |
| DUST | ppm Mg/kg | ≤100 | ≤100 | ≤100 | ≤100 | ≤100 | ≤100 | ≤100 | ≤100 |
| Melting Point | ºC | 244+/-2 | 244+/-2 | 244+/-2 | 244+/-2 | 244+/-2 | 244+/-2 | 244+/-2 | 244+/-2 |
| Water Content | wt% | ≤0.4 | ≤0.4 | ≤0.4 | ≤0.4 | ≤0.4 | ≤0.4 | ≤0.4 | ≤0.4 |
| Wt.of100Chips | g | 1.40+/-0.10 | 1.40+/-0.10 | 1.40+/-0.10 | 1.40+/-0.10 | 1.40+/-0.10 | 1.40+/-0.10 | 1.40+/-0.10 | 1.40+/-0.10 |
1. PET is mainly used for fibers, and a small amount is used for films and engineering plastics.
2. Another use of PET is blow molding products, which are used in various bottles, such as water bottles, carbonated beverage bottles, and oil bottles.
1100kg/bag 22tons/container or as customer's request
