Audited Supplier
HDPE Rod
PE
1000X2000 1200X2400
White,Yellow and Others
30~40 MPa
1-350mm
Low Water Absorption
Haiteng
Wooden Box
SGS
Jiangsu Yangzhong
39209910
Product Description
HDPE Rod Plastic Rod with 100% Virgin Material
HDPE, the full name is high density polyethylene. The higher density improves its tensile strength ,surface hardness and heat deflection temperature. It is widely used because of its good impact resistance, nice chemical resistance, low water absorption and good resistance to UV.
Characteristics
-Good fatigue and wear resistance
-Super low water absorption
-Cold resistant
-Good surface smoothness
-Good protection against stress cracking
-Low steam permeability
-Good electrical insulation
-Environmental friendly
-Recyclable
Images
Applications
1.Furnitures, doors ,windows ,chopping boards
2.Water storage box
3.Playground barriers
Technical Data Sheet
HDPE, the full name is high density polyethylene. The higher density improves its tensile strength ,surface hardness and heat deflection temperature. It is widely used because of its good impact resistance, nice chemical resistance, low water absorption and good resistance to UV.
Characteristics
-Good fatigue and wear resistance
-Super low water absorption
-Cold resistant
-Good surface smoothness
-Good protection against stress cracking
-Low steam permeability
-Good electrical insulation
-Environmental friendly
-Recyclable
Images
Applications
1.Furnitures, doors ,windows ,chopping boards
2.Water storage box
3.Playground barriers
Technical Data Sheet
| PROPERTIES | Test Method | Unit | Value |
| I.Physical Properties | |||
| Density | ISO 1183 | g/cm3 | 0.95~0.96 |
| Water absorption 24hrs | ISO 62 | % | 0.01 |
| II.Thermal Properties | |||
| Heat deflection temperature - HDT/A | ISO 75-2 | ºC | 55 |
| Min. service temperature | ºC | -30 | |
| Max. service temperature-Long Term | ºC | 90 | |
| Thermal conductivity at 23 ºC | DIN 11359 | W/(K*m) | 0.42 |
| Coefficient of linear thermal expansion | ISO 11359 | 10-4*K-1 | 1.5 |
| Flammability Rating(6mm thickness) | UL 94 | - | HB |
| III.Mechanical Properties at 23ºC | |||
| Tensile strength at yield | ISO 527-2 | MPa | 27 |
| Tensile strength at break | ISO 527-2 | Mpa | 35 |
| Elongation at break | ISO 527-2 | % | 700 |
| Modulus of elasticity after tensile test | ISO 527-2 | MPa | 1,000 |
| Modulus of elasticity after flexural test | ISO 178 | MPa | 1,000 |
| Hardness - Shore D | DIN 53505 | 64 | |
| Charpy impact strength | ISO 179 | kJ/m2 | N. B. |
| Friction coefficient | DIN 53375 | 0.3 | |
| IV.Electrical Properties at 23ºC | |||
| Dielectric constant at 1 MHz | IEC 60250 | 106Hz | 2.3 |
| Dielectric loss factor at 1 MHz | IEC 60250 | 106Hz | 3.1 |
| Volume resistively | IEC 60093 | Ohm (Ω) * cm | >1016 |
| Surface resisively | IEC 60093 | Ohm (Ω) | >1015 |
| Dielectric strength | IEC 60243-1 | kV/mm | 17 |
| NOTE: 1 g/cm3 = 1,000 kg/m3, 1 Mpa = 1 N/mm2, 1kV/mm = 1 MV/m | |||
