High Efficiency Submersible Axial Flow Pump

Burn free and leak proof

Power Power
7.5kW-2200kW

Flow Traffic Head lift
300 -70000m3/h                    5-20m

Speed speed
177 -2900r/min

Diameter 200-2400mm

Voltage Voltage 380V /660V/3KW/6KW/10KW

•   Transport medium:  clean water, rainwater, river water, sewage,  wastewater and other liquids with similar physical and chemical properties to water;
•   Output medium temperature+ 45 ° C;
•   The pH value of the pumped liquid is between 4-10;
•   Minimum water level: to the motor housing during full load operation;
•   Power frequency: 50Hz.

Mechanical seal
Adopting imported brands such as EagleBorgman. The failurerate has dee. "eased from 2 percent to 0.5 percent.
Mechanical seal
The machine seal adopts imported brands such as Borgman, dynamic and static failure adopts high-performance alloy material, and the failure rate of the machine seal is reduced from 2% to 0.5%.

1-Waterproof connection room, two-stage cable sealing and
fixing. Prevent excessive stretching and bending of cables
Water pressure sealed wiring room. The two-section cable is sealed and fixed to prevent excessive stretching and bending of the cable
To meet your safety requirements.

2.Waterproof motor, whose protection degree is up to IP68,
stator
insulation degree reaches F.Equipped with temperature
sensor, the rotor and main axis are subject to the dynamic
balancing test.
Waterproof motor, protection IP68, stator insulation class F, temperature sensor,
The rotor and spindle are tested for dynamic balance.

3.Imported bearings, durable and durable; Double layer alloy
mechanical seal, reliable and stable
Imported bearing, durable, double alloy mechanical seal, reliable and stable.

4.Monitoring devices provide feedback on equipment
operation at any time to ensure efficient operation of the
equipment
Monitor abusive clearance feedback equipment operation, so as to ensure efficient operation of equipment, bearing
Temperature sensors are installed at all places

5.Based on the most authoritative international ANSVHI 9.8
design standard.Inflow rotation angle<S 0;
Weighted average allowable error of axial
velocity<10%; There is no air coil at the suction port of the
water pump.
Based on the most authoritative ANSVHI9.8 design standard, the inflow rotation Angle <S• axial speed
The weighted average allowable error is <10%. No air is involved in the suction inlet of the pump.

6.Comply with GB/f 24674-2021;
All pumps are subject to the normal performance test
according to standards ISO 9906-2012
Comply with GB/f24674-2021, according to IS09906-2012 standard for routine performance testing
Try.

Basket grille
Mesh type, hole diameter D is 80% of the pump
diameter;
High anti-corrosion, high anti-rust;
The material is AISl304 material or above;
Any caliber, fully customized.
Basket grille
Mesh type, hole diameter D is 80% of the water pump diameter;
Anti-rust and anti-corrosion;
The material should be AISI304 material or above;
Any caliber, fully customized.

Mesh pocket grille
Using corrosion-resistant flexible material, the
head loss is small, the weight is light, and the
installation and maintenance are convenient.
A mesh grid
The use of anti-corrosion flexible materials, small head loss, light weight, safe
Convenient installation and maintenance.

Scope of use:
Farmland irrigation and drainage; Urban sewage drainage system; Industrial water and cooling water in the process; Water diversion project in water conservancy

we are Shijiazhuang Boda Industrial Pump Co.,Ltd from china .
We mainly operate slurry pumps, pump driven equipment, pump parts & resistance-wearing castings.
We can do OEM for buyers . 
We can produce products according to buyers' drawings . 
We can keep products quality ,material ,shipping and offer good service on after sales . 
We can do many materials for rubber and metallic Spare Parts .