CL Drum Gear Coupling

♦Features
1. Tooth coupling has a small radial dimension and large load-carrying capacity. It is often used for shafting transmission under low-speed and heavy-load conditions. Tooth coupling with high accuracy and dynamic balance can be used for high-speed transmission.
2. It has the ability to compensate for the deviation of radial, axial and angular equiaxed.
3. It has a compact structure, small turning radius, large bearing capacity, high transmission efficiency, low noise, and a maintenance cycle.






♦CL Gear Coupling Main Dimension And Parameter
Model | Nominal Torque KN·m | Speed rpm | Bore d1,d2,dz | Length of Bore | A | B | D | D1 | D2 | C | C1 | C2 | e | Rotary Inertia kg·m | Mass kg | |
Y | J1 Z2 | |||||||||||||||
L | ||||||||||||||||
mm | ||||||||||||||||
CL1 | 710 | 3780 | 18,19 | 42 | 30 | 49 | 106 | 170 | 110 | 55 | 16 | - | - | 12 | 0.03 | 7.8 |
20,22,24 | 52 | 38 | 6 | 18.5 | 18.5 | |||||||||||
25,28 | 62 | 44 | 2.5 | 14 | 18.5 | |||||||||||
30,32,35,38 | 82 | 60 | 11 | - | ||||||||||||
40 | 112 | 84 | ||||||||||||||
CL2 | 1400 | 3000 | 30,32,35,38 | 82 | 60 | 75 | 134 | 185 | 125 | 70 | 2.5 | 13 | 22 | 12 | 0.05 | 12.5 |
40,42,45 | 112 | 84 | 28 | |||||||||||||
48,50 | ||||||||||||||||
CL3 | 3150 | 2400 | 40,42,45 | 112 | 84 | 92 | 170 | 220 | 150 | 90 | 2.5 | 15 | 28 | 18 | 0.13 | 26.9 |
48,50,55,56 | ||||||||||||||||
60 | 142 | 107 | 36 | |||||||||||||
CL5 | 8000 | 1680 | 50,55,56 | 112 | 84 | 145 | 220 | 290 | 200 | 130 | 5 | 30 | 40 | 25 | 0.45 | 55.8 |
60,63,65,70 | 142 | 107 | ||||||||||||||
71,75 | ||||||||||||||||
80,85,90 | 172 | 132 | ||||||||||||||
CL6 | 11200 | 1500 | 60,63,65 | 142 | 107 | 160 | 246 | 320 | 230 | 140 | 5 | 25 | - | 25 | 0.70 | 79.9 |
70,71,75 | ||||||||||||||||
80,85,90,95 | 172 | 132 | ||||||||||||||
100,110 | 212 | 167 | ||||||||||||||
CL7 | 18000 | 1270 | 65,70,71,75 | 142 | 107 | 185 | 286 | 350 | 260 | 170 | 5 | 40 | 40 | 30 | 1.15 | 109.5 |
80,85,90,95 | 172 | 132 | 25 | 45 | ||||||||||||
100,110,120 | 212 | 167 | ||||||||||||||
CL8 | 22400 | 1140 | 80,85,90,95 | 172 | 132 | 210 | 325 | 380 | 315 | 190 | 5 | 35 | 45 | 30 | 2.38 | 133.8 |
100,110,120 | 212 | 167 | ||||||||||||||
130,140 | 252 | 202 | 30 | |||||||||||||
CL9 | 28000 | 1000 | 90,95 | 172 | 132 | 220 | 335 | 430 | 365 | 210 | 5 | 40 | - | 30 | 3.55 | 171 |
100,110,120,125 | 212 | 167 | 30 | |||||||||||||
130,140,150 | 252 | 202 | ||||||||||||||
160 | 302 | 242 | ||||||||||||||
CL10 | 50000 | 850 | 110,120,125 | 212 | 167 | 245 | 365 | 490 | 420 | 260 | 5 | 30 | - | 30 | 7.00 | 275.8 |
130,140,150 | 252 | 202 | ||||||||||||||
160,170,180 | 302 | 242 | ||||||||||||||
CL11 | 71000 | 750 | 120,125 | 212 | 167 | 280 | 405 | 545 | 470 | 330 | 5 | 40 | - | 35 | 13.75 | 385 |
130,140,150 | 252 | 202 | ||||||||||||||
160,170,180 | 302 | 242 | 35 | |||||||||||||
190,200,220 | 352 | 282 | ||||||||||||||
CL12 | 100000 | 660 | 140,150 | 252 | 202 | 350 | 485 | 590 | 520 | 340 | 5 | 45 | - | 35 | 21.5 | 540 |
160,170,180 | 302 | 242 | 38 | |||||||||||||
190,200,220 | 352 | 282 | ||||||||||||||
240,250 | 410 | 330 | ||||||||||||||
CL13 | 140000 | 600 | 160,170,180 | 302 | 242 | 375 | 524 | 680 | 590 | 380 | 7.5 | 45 | - | 40 | 40.00 | 798.3 |
190,200,220 | 352 | 282 | ||||||||||||||
240,250,260 | 410 | 330 | ||||||||||||||
280 | 470 | 380 | ||||||||||||||
CL14 | 200000 | 540 | 180 | 302 | 242 | 405 | 565 | 730 | 650 | 450 | 7.5 | 50 | - | 40 | 53.75 | 976.6 |
190,200,220 | 352 | 282 | ||||||||||||||
240,250,260 | 410 | 330 | ||||||||||||||
280,300,320 | 470 | 380 | ||||||||||||||
CL15 | 250000 | 480 | 200,220 | 352 | 282 | 480 | 644 | 780 | 700 | 480 | 7.5 | 50 | - | 40 | 81.25 | 1182.5 |
240,250,260 | 410 | 300 | ||||||||||||||
280,300,320 | 470 | 380 | ||||||||||||||
340,360 | 550 | 450 | ||||||||||||||
CL16 | 355000 | 425 | 240,250,260 | 410 | 330 | 535 | 720 | 900 | 785 | 530 | 10 | - | - | 50 | 150 | 1936 |
280,300,320 | 470 | 380 | ||||||||||||||
340,360,380 | 550 | 450 | ||||||||||||||
400 | 650 | 540 | ||||||||||||||
CL17 | 560000 | 380 | 260 | 410 | 330 | 625 | 800 | 1000 | 885 | 630 | 10 | - | - | 50 | 285 | 2700 |
280,300,320 | 470 | 380 | ||||||||||||||
340,360,380 | 550 | 450 | ||||||||||||||
400,420,440,450 | 650 | 540 | ||||||||||||||
CL18 | 710000 | 330 | 300,320 | 470 | 380 | 71 | 900 | 1100 | 990 | 710 | 10 | - | - | 50 | 400 | 3669 |
340,360,380 | 550 | 450 | ||||||||||||||
400,420,440,450 | 650 | 540 | ||||||||||||||
460,480,500 | ||||||||||||||||
CL19 | 1000000 | 300 | 360,380 | 550 | 450 | 730 | 910 | 1250 | 1090 | 800 | 15 | - | - | 60 | 675 | 5138 |
400,420,440,450 | 650 | 540 | ||||||||||||||
460,480,500 | 800 | 680 | ||||||||||||||
530,560 |
1. The coupling mass and rotary inertia are approximations calculated by the minimum diameter and the maximum length of the bore.
2. Bore diameter dz <140mm.
3. J1-type bore does not need shaft end baffle as required.
4. This standard applies only to old products.

Advanced and reasonable process, complete detection means. Our company actively introduces foreign advanced technology and equipment, on the basis of the condition, we make full use of the advantage and do more research and innovation. Strict to high quality and operate strictly in accordance with the ISO9000 quality certification system standard mode.
Our company supplies different kinds of products. High quality and reasonable price. We stick to the principle of "quality first, service first, continuous improvement and innovation to meet the customers" for the management and "zero defect, zero complaints" as the quality objective.



1. Design Services
2. Product Services
raw materials → Cutting → Forging →Rough machining →Shot blasting →Heat treatment →Testing →Fashioning →Cleaning→ Assembly→Packing→Shipping
3. Samples Procedure
We could develop the sample according to your requirement and amend the sample constantly to meet your need.
4. Research & Development
We usually research the new needs of the market and develop new models when there are new cars in the market.
5. Quality Control
Every step should be a particular test by Professional Staff according to the standard of ISO9001 and TS16949.
Q 1: Are you a trading company or a manufacturer?
A: We are a professional manufacturer specializing in manufacturingvarious series of couplings.
Q 2:Can you do OEM?
Yes, we can. We can do OEM & ODM for all customers with customized PDF or AI format artwork.
Q 3:How long is your delivery time?
Generally, it is 20-30 days if the goods are not in stock. It is according to quantity.
Q 4: Do you provide samples? Is it free or extra?
Yes, we could offer the sample but not for free. Actually, we have an excellent price principle, when you make the bulk order the cost of the sample will be deducted.
Q 5: How long is your warranty?
A: Our Warranty is 12 months under normal circumstances.
Q 6: What is the MOQ?
A: Usually our MOQ is 1pcs.
Q 7: Do you have inspection procedures for coupling?
A:100% self-inspection before packing.
Q 8: Can I have a visit to your factory before the order?
A: Sure, welcome to visit our factory.
Q 9: What's your payment?
A:1) T/T.