Audited Supplier
LDP
Provide
Provide
CE, ISO9001, SGS
New
Air Operation+Ground Operation
31.5m
20t
Single Girder
Beam
20t
Customized
7-31.5m
A3
Huasui
Santard Packing
7-31.5m
Henan, China
8426112000
Product Description
Product descriptions from the supplier
Overview
Offset Trolley Single Girder Overhead Crane
Offset trolley single girder overhead cranes are girder cranes with angular trolley structure. It has better height space utilization compared with single girder electric overhead travelling cranes.
Offset trolley single girder overhead cranes mainly consists of main girder, end girder, angle trolley, trolley running mechanism, electrical equipment and other parts. All other parameters are the same as single girder electric overhead travelling cranes type.
* Standard Capacity: 1t/2t/3t/5t/10t/16t/20t or customized on demand
* Span length: 7.5m-28.5m
* Lifting height: 6m/9m/12m/18m/24m/30m
* Work duty: A3/A4
* Rated voltage: 220V/380V/400V/415V/660V, 50-60Hz, 3ph AC
* Crane control mode: Floor control / Remote control
* Traveling speed: 20-30m/min
* Span length: 7.5m-28.5m
* Lifting height: 6m/9m/12m/18m/24m/30m
* Work duty: A3/A4
* Rated voltage: 220V/380V/400V/415V/660V, 50-60Hz, 3ph AC
* Crane control mode: Floor control / Remote control
* Traveling speed: 20-30m/min
Main Girder
Main girder is the main bearing part of the crane, its structure is made of U-shaped groove, inclined cover plate, rib plate and I beam steel plate, its upper arc is ((1/1000~1.4/1000)S, when the rated lifting weight and the hoist's self-weight are located in the middle of the span, the degree of camber caused is not lower than the horizontal line, and there is no permanent deformation
during normal operation.
Main girder is the main bearing part of the crane, its structure is made of U-shaped groove, inclined cover plate, rib plate and I beam steel plate, its upper arc is ((1/1000~1.4/1000)S, when the rated lifting weight and the hoist's self-weight are located in the middle of the span, the degree of camber caused is not lower than the horizontal line, and there is no permanent deformation
during normal operation.
Electric Hoist
Electric hoist is to be used on single girder overhead crane, each electric hoist will perform dynamic and static load test, rise and drop pressure tests. The baking paint process is adopted to enhance the adhesion of the paint film and improve the appearance quality.
Electric hoist is to be used on single girder overhead crane, each electric hoist will perform dynamic and static load test, rise and drop pressure tests. The baking paint process is adopted to enhance the adhesion of the paint film and improve the appearance quality.
End Girder
End girder is located at both ends of the main beam, is bolted to the main beam by flange plats. It's box structure, composed of U-shaped groove, lower cover plate, reinforcement plate, and rib plates formed by steel plate rolling or welded steel plates.
End girder is located at both ends of the main beam, is bolted to the main beam by flange plats. It's box structure, composed of U-shaped groove, lower cover plate, reinforcement plate, and rib plates formed by steel plate rolling or welded steel plates.
Crane Motor
The crane motor adopts ZDY(D) series cone rotor brake motor or soft starter motor. The standard motor insulation class is B and the protection class is IP44. The motor has the characteristics of good heat dissipation, long service life, safety and reliability.
The crane motor adopts ZDY(D) series cone rotor brake motor or soft starter motor. The standard motor insulation class is B and the protection class is IP44. The motor has the characteristics of good heat dissipation, long service life, safety and reliability.
Products | Span/m | Lifting Height/m | Power Supply Voltage |
1 ton single girder overhead crane | 7.5-28.5 | 6-30 | 220V-660V, 50-60Hz, 3ph AC |
2 ton single girder overhead crane | 7.5-28.5 | 6-30 | 220V-660V, 50-60Hz, 3ph AC |
3 ton single girder overhead crane | 7.5-31.5 | 6-30 | 220V-660V, 50-60Hz, 3ph AC |
5 ton single girder overhead crane | 7.5-31.5 | 6-30 | 220V-660V, 50-60Hz, 3ph AC |
10 ton single girder overhead crane | 7.5-31.5 | 6-30 | 220V-660V, 50-60Hz, 3ph AC |
16 ton single girder overhead crane | 7.5-31.5 | 6-30 | 220V-660V, 50-60Hz, 3ph AC |
20 ton single girder overhead crane | 7.5-31.5 | 6-30 | 220V-660V, 50-60Hz, 3ph AC |
Huasui has 15 years of experience in crane and hoist design and manufacturing, 3 production factories covering an area of 168000 square meters, 10 production lines with annual production capacity 500 sets. It has more than 800 employees, including more than 20 technicians and more than 10% senior engineers. The factories have modern crane manufacturing and assembly equipment, and introduces European advanced management, process flow and quality control system to ensure safe, reliable and high quality cranes for customers, making customers' logistics operations easier and creating long-term value for customers.
FAQ
B: Yes! We can customize all kinds of cranes according to your requirements. You just need to tell us your demands.
A:Which industries do you service?
A:Which industries do you service?
B: We service many industries including machinery, metallurgy, railway and so on. High quality products in different fields will play an important role.
A:Which areas do you service?
A:Which areas do you service?
B: We have a huge market both at home and abroad. We have exported our cranes to many countries, especially European, Africa and so on.
A: How do you guarantee the quality?
B: We will constantly check the quality during the manufacturing process, and strictly test the equipment before shipment, and we will also send you a quality certificate.
B: We will constantly check the quality during the manufacturing process, and strictly test the equipment before shipment, and we will also send you a quality certificate.
A:What are the main products?
B: Our main products are overhead and gantry cranes. Different products have different models and application scenarios.
A:What international certifications has your company passed?
B: Our main products are overhead and gantry cranes. Different products have different models and application scenarios.
A:What international certifications has your company passed?
B: Our cranes has passed CE, lSO, GOST, SGS, TUV, BV, and so on.
