Nylon Pleated Filter Element.

Characteristics and features

• Excellent high-tem resistance and alkali resistance.

• All the compositions reach up to the requirement of the biological testing characteristics of USP Class 6 plastic products at 121ºC and the food contact materials listed in the relevant regulations of Chapter 21 of the Federal Regulations of the United States (CFR). They also conform to the requirements of China's "Standard for Hygienic Safety Evalution of Equipment and Protective Materials in Drinking Water" (2001) for drinking water transport and distribution equipment.

• The sampling of filter element successfully passed the bacterial challenge test required by regulations, LRV≥7.Integrity can be maintained after repeated high-pressure disinfection.

• Each filter element should pass the integrity test before leaving the factory. The limitations of integrity testing were correlated with the results of bacterial challenge experiments.

• It is manufactured under ISO 9001 and ISO 14001 systems and Class 100 environment.

• Natural hydrophilicity, easy to wet and fast to test integrity.

• High tensile strength, suitable for applications with high impurity content and high viscosity.

• Production and usage are traceable.
  
  

• 

  Material of filter element components:
  Filter material : Nylon Membrane

  Supports/Diversion : PP

  Core/Cover/End cover/End caps : PP

  Sealed leads/Fins : PP,Built in stainless steel

  O-Ring : 222,226 silicon rubber etc.

  Sealing technology : Hot melt without adhesives

  
  

  Technical specifications and operating parameters

   

  Size	Diameter: 2.75"(69 mm) Length: 5"/10"/20"/30"/ 40" etc.
  Filtration area	Single 10" filter element is about 0.65m²
  Dissolution(20ºC)	Testing The filters without pre-washing . After 24 hours immersion in water, the dissolution was less than 30 mg/10" filters.
  Minimum Bubble Point of Integrity Test Data	0.22μm: > 0.25MPa in Water 0.45μm : > 0.18MPa in Water Other options:0.1μm,0.65μm
  Conditions of steam sterilization and hot water sterilization	Sterilization temperature: hot water 85ºC Steam in place 121 ºC/30 min,more than 15 times
  Maximum pressure difference and temperature	Maximum operating temperature: 85 C/0.2 MPa;  25 ºC (≥ 0.4 MPa)
  Typical flow rate (Water, 20ºC)	0.1um:5lpm/0.02MPa/10" 0.22um:8.3lpm/0.02MPa/10" 0.45um:10lpm/0.02MPa/10" 0.65um:33lpm/0.02MPa/10"

  
  Typical application

• Sterilization filtration of LVP, fine needle, freeze-dried and spray dried drug.

• Sterilization filtration and Mycoplasma removal filtration of animal serum, liquid medium, buffer solution, supplement water, etc..

• Sterilization filtration of various solvents in pharmaceutical industry.

• Sterilization filtration of various process water and pharmaceutical water

• Terminal filtration of bottled water, draft beer, wine, yellow wine, soft drinks, syrups, etc. in the food and beverage industry.
   

  Ordering information

   

  1	2		3	4	5	6	7
  NL	0.22	---	10	A	S	P	--X

   

  1	Membrane	Hydrophilic NL membrane
  2	Pore size	1 / 0.1 / 0.22 / 0.45μm
  3	Length	5" / 10" / 20" / 30" / 40"
  4	Connector/End Cover A/AA/B/BB/C/CC/D/E/EE/F	Spear+222 Spear+222adapter with encapsulated reinforcing stainless steel ring Flat+222 Flat+222adapter with encapsulated reinforcing stainless steel ring Spear+226 Spear+226adapter with encapsulated reinforcing stainless steel ring Flat+Flat Flat+226 Flat+226adapter with encapsulated reinforcing stainless steel ring Flat+215 Spear+3 Flange Bayonet adapter
  5	Gasket Material S,E,F,FF	S: Silicon rubber E: EPDM rubber F: Fluorine rubber FF: Encapsulated fluoroelastomer
  6	Application P	Pharmaceutical grade for bio-pharmaceutical&food and beverage industry
  7	Special Specification Remarks	Standard Specification Default