Audited Supplier
bagging film
Nylon
Medium
Infusion Consumables
65 Um
Max 12 Meter
Light Yellow
Center Fold, Sheet, Lay Flat Tube
34 MPa
350%
Infusion Process
High Temperature Resistance
Plastic Film
Co-Extruded
Nylon
JLON
Roll
65um/75um
Changzhou, China
3920920000
Product Description
A SERIES OF MATERIALS USED FOR VACUUM CONSUMABLES:
RELEASE FILM:
RF35 Perforated Release Film is a red/blue color PE release film that is designed for low cost applications. It will release from epoxy, polyester and vinyl ester resin systems. It is suitable for resin cure temperature up to 250°F (121°C).
RF35 Perforated Release Film is a red/blue color PE release film that is designed for low cost applications. It will release from epoxy, polyester and vinyl ester resin systems. It is suitable for resin cure temperature up to 250°F (121°C).
Reference:
Example:RF35-1200-500
Material: PE
Thickness: 35um
Width:1200mm
Length:500m
Example:RF35-1200-500
Material: PE
Thickness: 35um
Width:1200mm
Length:500m
Application:
Perforated Release Film RF35 is most commonly used in vacuum infusion processing.
Features And Benefits: Red/Blue color is visible on laminate surface.
Good value for low to medium temperature applications.
Available in P16 perforation style, especially for infusion applications.
Technical Parameters:
Material type: PE
Elongation at break: 500 % ATP 5042
Tensile strength: 4350 psi (30 MPa) ATP 5042
Maximum use temperature: 250°F (121°C)
Materials to avoid: Phenolic resins/Strong oxidizers
Color: Red/blue
2) Vacuum Bagging Film:
Vacuum bag BF65 is a wide multi-layer extruded Nylon film providing multiple layers of safety. These multi layers reduce the concerns of pinholes,
Weak spots, brittleness and inconsistency in films. This Vacuum bag is strong, has a high elongation and is suitable for cure temperature up to 170C.
We provide various width and roll length , for more information please contact us.
Features:
High temperature resistance suitable for multi resin systems.
Wider films save time and money spent seaming film for large parts.
Reduce scrap risk due to vacuum loss with multi-layered vacuum security.
Wider films and good mechanical strength reduce risk of scrap parts due to leakage at seams.
Application:
Vacuum bagging applications .(not recommended for autoclave application).
Vacuum bagging applications .(not recommended for autoclave application).
Typical Specifications:
| Physical Property | Units | Specification | Test Method |
| Thickness | um | 65 | |
| Material | - | Nylon,Multi-Layer | |
| Color | - | Ligth Yellow | |
| Working Temperature | C | Max 170 | |
| Elongation | % | 350 | ASTM D882 |
| Tensile strength | Mpa | 34 | ASTM D882 |
| Roll Width | m | Max 12 | - |
| Roll length | m | Max 200 | - |
| Forms | - | V,W Fold | - |
3) Infusion Mesh:
Resin distribution media IM120 is HDPE extruded net/mesh designed to assist resin flow through your part during the VARTM process. Our resin distribution medium works well with polyester ,vinyl ester and epoxy resins. This resin distribution media is low profile and tight construction, the resin flows more easily and efficiently (little waste) throughout the lay-up when using this resin distribution media.
We provide different area weight and width, for more information please contact us.
Features:
Low resin waste.
This product is an extruded net/mesh and does not fray when cut.
The color fastness is good under working temperature, will not contaminate the products.
Application:
Resin distribution of Vacuum bagging applications.
Typical Specifications:
| Physical Property | Units | Specification | Physical Property | Units | Specification |
| Thickness | mm | 1.0+-0.2 | Thickness | mm | 1.0+-0.2 |
| Width | m | Max 4 | Width | m | Max 4 |
| Length | m | 100 | Length | m | 100 |
| Color | - | Green | Color | - | Green |
| Material | - | HDPE | Material | - | HDPE |
| Working Temperature | C | 120 | Working Temperature | C | 120 |
| Style | - | Weave | Style | - | Rhombic |
| Area Weight | g/m2 | 120-240 | Area Weight | g/m2 | 100-240 |
4) Spiral Tube:
This plastic spiral tube is made of HDPE and used to provide a very free‐lowing channel through which the resin is distributed near the point where the resin is first fed into the composite. Resin flows freely through the center of the spiral tube, but just as easily out of the spirals in the side, allowing resin to be supplied all the way along an edge of the composite.
Features:
Low material cost.
HDPE material, strong tube wall makes the spiral tube not deformed under atmospheric pressure.
Application:
Resin distribution of Vacuum bagging applications.
Typical Specifications:
| Physical Property | ID*OD(MM) | ID*OD(MM) | ID*OD(MM) | ID*OD(MM) | ID*OD(MM) |
| 8*10 | 10*12 | 12*14 | 16*19 | 19*23 | |
| Material | HDPE | HDPE | HDPE | HDPE | HDPE |
| Thickness | 1mm | 1mm | 1mm | 1.5mm | 2mm |
| Color | White | White | White | White | White |
| Working Temperature | 120C | 120C | 120C | 120C | 120C |
| Length | 100m | 100m | 100m | 100m | 100m |
5) Sealant Tape:
Sealant tape ST12 is synthetic rubber sealant tape used to provide a continuous airtight seal between the vacuum bag and the mold around the perimeter of the mold. The sealant tape may also be used to seal the point where the manifold enters the bag and to repair leaks in the bag or plumbing.The sealant tape ST12 is a cost effective vacuum bag sealant tape for room and medium temperature applications. It has been specially formulated to provide excellent tack, firm feel, good clean-up and long shelf-life.
Sealant tape ST12 is synthetic rubber sealant tape used to provide a continuous airtight seal between the vacuum bag and the mold around the perimeter of the mold. The sealant tape may also be used to seal the point where the manifold enters the bag and to repair leaks in the bag or plumbing.The sealant tape ST12 is a cost effective vacuum bag sealant tape for room and medium temperature applications. It has been specially formulated to provide excellent tack, firm feel, good clean-up and long shelf-life.
Features:
Lower material cost.
Long shelf life reduces waste.
Easy clean up reduces cost and times of tool cleaning.
Different tack version has better tack for different environments, easy to use.
Application:
Vacuum bagging applications. (Not recommended for autoclave application).
Typical Specifications:
| Physical Property | Units | Specification | Test Method |
| Thickness | mm | 3 | |
| Width | mm | 12 | |
| Length | m | 15 | |
| Color | - | Yellow | |
| Material | - | Sythetic Butyl Rubber | |
| Working Temperature | C | Max 200 | |
| Elongation | % | 680 | ASTM C736 |
| Peel strength | 300mm/Min @23C | Glass ≥ 16.3 | ASTM D3330 |
| 300mm/Min @23C | Stainless Steel ≥12.5 | ||
| Shear strength | 250mm/Min @23C | Glass ≥ 35 | GB/T12952 |
| 250mm/Min @23C | Stainless Steel ≥37 |
6) Peel Ply:
The peel ply PL85 is Nylon (PA66) woven fabric which is high in quality, yet inexpensive. The peel ply PL85 is designed to work in VARTM vacuum resin infusion or hand lay-up processes. The peel ply PL85 assist or eliminate the need for sanding or abrading on your composite laminate.
We provide different width and roll length , for more information please contact us.
Features:
Low material cost.
High temperature resistance suitable for multi resin systems.
Easy to remove, reducing the possibility of the peel ply being left one the parts.
Application:
Vacuum bagging applications , hand lay-up process.
Typical Specifications:
| Physical Property | Units | Specification | Test Method |
| Weight | g/m2 | 85 | - |
| Material | - | Nylon,PA66 | - |
| Color | - | White/Red tracers | - |
| Working Temperature | C | Max 190 | - |
| Thickness | mm | 0.15 | - |
| Standard Roll Width | m | 1.8 | - |
| Standard Roll length | m | 200 | - |
FAQ
Q1.Can your company customize products?
A: Yes, We usually discuss with customers and help them find solutions.
Q2. How can I get a sample from you to check quality?
A: Usually a sample will be prepared within one week after specification agreed.
Q3. What about your delivery time? Can we receive our goods on time?
A: Usually around 2-3 weeks after order confirmed. Exact delivery time depends on order quantity and Off-season/ busy season.
Q4. What is the Guarantee to buy your products? How to resolve quality complaints?
A: Offer TDS of each lot of production for confirmation before delivery.Once you have any quality problem, you can provide samples /pictures /test data. With our quality tracking system, we will give you feedback in short time. If the quality problem confirmed,we will send you replacement or make refund as you like.
Q5. What are your terms of payment?
A: Usually we do EXW, FOB, CIF, and DDU.
