Audited Supplier
1200V DIN Mounting DC Isolator Switch
Product Profile
EDS1 Series isolator Parallel wiring, larger aperture, much easier wiring. Suitable for distribution box module with lock installation. Arc extinction time less than 3ms.Modular design. 2 poles & 4poles optional. Comply with IEC60947-3(ed.3.2):2015, DC-PV1standard.
EDS1 series isolation switch is suitable for a power system with rated voltage DC 1200V or below and rated current 32A or below. The product can be used for infrequent switching-on and switching-off and can disconnect 1 - 2 MPPT lines at the same time. It is especially suitable for isolating lines in HVDC transmission and distribution systems, such as cutting off the high voltage DC current between solar panels and inverters.
Product Benefits
- Installed at any angle can achieve IP66 waterproof level
- UV resistance and V0 flame retardant material
- Contact Silver Plating, silver layer thickness to the industry's highest standards
- Arcing Time in 3ms
- Breather valve attached on the bottom of the isolator
- No Polarity
- Lockable at OFF position
- IEC/EN60947.3 standard and As 60947.3
- 5 years warranty, product insurance, and recall insurance available
Technical Data
| Main Parameters | EDS1/N EDS1/S | ||
| Rated Insulation Voltage | Ui | V | 1500 |
| Rated thermal current | Ith | A | 32 |
| Rated impulse withstand voltage | Uimp | V | 8000 |
| Rated short-circuit making capacity | Icw | A | 1 kA,1 S |
| Maximum cable section(incl.jumper) | |||
| Solid | mm2 | 4-16 | |
| Flexible | mm2 | 4-10 | |
| Flexible(+multicore cable end) | mm2 | 4-10 | |
| Torque | |||
| Tightening torque terminal screws M4. | Nm | 1.2-1.8 | |
| Tightening torque shell mounting screws ST4.2(304 stainless steel) | Nm | 1.5-2.0 | |
| Tightening torque knob screws M3 | Nm | 0.5-0.7 | |
| Switching on or off Torque | Nm | 0.9-1.3 | |
| The wiring Torque on Base | Nm | 1.1-1.4 | |
| General parameters | |||
| Knob Positions | 12 o'clock,OFF 3 o'clock,ON 9 o'clock,OFF 12 o'clock,ON | ||
| Electrical Life | Actual | 3000 Cycles | |
| Standard | 300 Cycles | ||
| Mechanical Life | Actual | 10000 Cycles | |
| Standard | 10000 Cycles | ||
| Number of DC poles | 2 or 4 | ||
| Operation temperature | °C | -40 to +85 | |
| Storage termperature | °C | -40 to +85 | |
| Pollution degree | 3 | ||
| Overvoltage category | III | ||
| IP rating of shafte and mounting nul | IP66 | ||
Data according to AS60947-3
| Main Contacts | Voltage | EDS1/N32 |
| Rated thermal current Ithe | 32 A | |
| Rated insulation voltage Ui | 1500 V | |
| Distance of contacts(per pole) | 8 mm | |
| Rated operational current Ie(DC-PV2) | ||
| 4 layers, only 2layers in series, with two load 1 2 | 300V | 32 A |
| 600V | 32 A | |
| 800V | 16 A | |
| 1000V | 9 A | |
| 4 layers, 4 layers in series, with one load 1 2 3 4 | 300V | 32 A |
| 600V | 32 A | |
| 800V | 32 A | |
| 1000V | 32 A |
Technical Data
| Main Parameters | EDS1/N EDS1/S | ||
| Rated Insulation Voltage | Ui | V | 1500 |
| Rated thermal current | Ith | A | 32 |
| Rated impulse withstand voltage | Uimp | V | 8000 |
| Rated short-circuit making capacity | Icw | A | 1 kA,1 S |
| Maximum cable section(incl.jumper) | |||
| Solid | mm2 | 4-16 | |
| Flexible | mm2 | 4-10 | |
| Flexible(+multicore cable end) | mm2 | 4-10 | |
| Torque | |||
| Tightening torque terminal screws M4. | Nm | 1.2-1.8 | |
| Tightening torque shell mounting screws ST4.2(304 stainless steel) | Nm | 1.5-2.0 | |
| Tightening torque knob screws M3 | Nm | 0.5-0.7 | |
| Switching on or off Torque | Nm | 0.9-1.3 | |
| The wiring Torque on Base | Nm | 1.1-1.4 | |
| General parameters | |||
| Knob Positions | 12 o'clock,OFF 3 o'clock,ON 9 o'clock,OFF 12 o'clock,ON | ||
| Electrical Life | Actual | 3000 Cycles | |
| Standard | 300 Cycles | ||
| Mechanical Life | Actual | 10000 Cycles | |
| Standard | 10000 Cycles | ||
| Number of DC poles | 2 or 4 | ||
| Operation temperature | °C | -40 to +85 | |
| Storage termperature | °C | -40 to +85 | |
| Pollution degree | 3 | ||
| Overvoltage category | III | ||
| IP rating of shafte and mounting nul | IP66 | ||
Data according to AS60947-3
| Main Contacts | Voltage | EDS1/N32 |
| Rated thermal current Ithe | 32 A | |
| Rated insulation voltage Ui | 1500 V | |
| Distance of contacts(per pole) | 8 mm | |
| Rated operational current Ie(DC-PV2) | ||
| 4 layers, only 2layers in series, with two load 1 2 | 300V | 32 A |
| 600V | 32 A | |
| 800V | 16 A | |
| 1000V | 9 A | |
| 4 layers, 4 layers in series, with one load 1 2 3 4 | 300V | 32 A |
| 600V | 32 A | |
| 800V | 32 A | |
| 1000V | 32 A |
FAQQ: Are you trading company or manufacturer ?
A: We are manufacturer. We have 30,000 square meters of self-owned plant.
Q: Do you have any certificates?
A: Yes,we have UL, TUV, CB, SAA, CCC, CE and other certifications.
Q: How do we make a quick response to customer , 5 inquiry ?
A: Our professional team will reply you online or by email,Skype, whatsApp and so on.
Q: Do you have any exporting experience?Which countries did you export to before?
A: We have lots of exporting experience and customers in many countries,such as America, Japan,Australia,UAE,Canada,Vietnam,Turkey,Thailand,Russia,UK,etc.
Q:Can you supply samples for checking ?
A: Yes, we can supply samples, pls contact for detailed required.
Q:How long is your delivery time?
A: Generally it is within 3days for small qty. Or it is around 15-20 days to a general order.
Q: What is the standard of package of your goods?
A: Export standard package or special package according to customer requirement.
Q:How about inspection?
A: We have the whole inspection system from raw material to end products include transient test, delay test,mechanical life test and so on.Q:What is the service offered by company?
A: We have the professional engineer team which can design and develop the mould to arrive different customer requirements. We also have the professional sales team to offer good service from pre-sale to after-sale.
