Audited Supplier
CY
380V/50Hz/3phase, According to Requirement
Siemens
CHIYU
Wood Pallet+Stretch Film Package
SUS304
Jiangsu Suzhou
Product Description
Pneumatic Conveyor
The positive pressure dense phase pneumatic conveying system uses compressed air as the conveying medium. In the pipeline, materials are transported in a low speed, sand dune state, fluidization or agglomeration state, which is called positive pressure dense phase pneumatic transportation. Generally, air compressor is used as the air source, and the delivery pressure can be 0.2mpa-0.5mpa according to different working conditions. According to the conveying characteristics, the system can be divided into two modes: positive pressure dense phase eddy current conveying and positive pressure dense phase pulse conveying. The conveying mode of materials in sand dune state or fluidization in the pipeline with low speed is called positive pressure dense phase eddy current conveying; the conveying mode of materials in the pipeline with low speed and agglomeration state is called positive pressure dense phase pulse conveying.
System features:
1. The working pressure is high, so it can realize long-distance and high-capacity transportation; the booster can realize ultra long-distance transportation;
2. Due to the low conveying speed of materials, the abrasion of conveying pipes and materials is less;
3. High material gas ratio, low gas consumption and low operation cost;
4. It can transport from single point to multi-point, and is easy to process design;
Basic parameters:
1. Conveying pressure: 0.2MPa ~ 0.5MPa (determined according to the specific gravity, distance and height of materials)
2. Required air source pressure: not less than 0.45MPa
3. Material gas ratio: 10kg ~ 85kg / kg
4. Conveying speed: initial 0.5m/s to end 12m / S
The negative pressure conveying system can be defined as a method of conveying powder or granular materials along a limited channel by means of suction.
Technical features:
There is no need to rotate the valve.
It can be transmitted from several starting points to a target point.
the material enters the pipeline under normal pressure, so it is easy to add the material.
There is no need to cool the conveying gas in the conveying process.
even if the pipe connection and sealing are not good, it will not cause powder leakage.
the material receiving hopper is always in the negative pressure state, and the negative pressure resistance performance needs to be considered.
the maximum conveying pressure is only - 0.4 to - 0.5kpa, so the conveying distance and conveying capacity are limited.
It is almost impossible to realize dense phase transportation.
compared with the positive pressure transportation, the energy consumption is higher under the same conditions.
The positive pressure dense phase pneumatic conveying system uses compressed air as the conveying medium. In the pipeline, materials are transported in a low speed, sand dune state, fluidization or agglomeration state, which is called positive pressure dense phase pneumatic transportation. Generally, air compressor is used as the air source, and the delivery pressure can be 0.2mpa-0.5mpa according to different working conditions. According to the conveying characteristics, the system can be divided into two modes: positive pressure dense phase eddy current conveying and positive pressure dense phase pulse conveying. The conveying mode of materials in sand dune state or fluidization in the pipeline with low speed is called positive pressure dense phase eddy current conveying; the conveying mode of materials in the pipeline with low speed and agglomeration state is called positive pressure dense phase pulse conveying.
System features:
1. The working pressure is high, so it can realize long-distance and high-capacity transportation; the booster can realize ultra long-distance transportation;
2. Due to the low conveying speed of materials, the abrasion of conveying pipes and materials is less;
3. High material gas ratio, low gas consumption and low operation cost;
4. It can transport from single point to multi-point, and is easy to process design;
Basic parameters:
1. Conveying pressure: 0.2MPa ~ 0.5MPa (determined according to the specific gravity, distance and height of materials)
2. Required air source pressure: not less than 0.45MPa
3. Material gas ratio: 10kg ~ 85kg / kg
4. Conveying speed: initial 0.5m/s to end 12m / S
5. Conveying distance: 50m high, 1500m horizontal
Vacuum conveying systemsThe negative pressure conveying system can be defined as a method of conveying powder or granular materials along a limited channel by means of suction.
Technical features:
There is no need to rotate the valve.
It can be transmitted from several starting points to a target point.
the material enters the pipeline under normal pressure, so it is easy to add the material.
There is no need to cool the conveying gas in the conveying process.
even if the pipe connection and sealing are not good, it will not cause powder leakage.
the material receiving hopper is always in the negative pressure state, and the negative pressure resistance performance needs to be considered.
the maximum conveying pressure is only - 0.4 to - 0.5kpa, so the conveying distance and conveying capacity are limited.
It is almost impossible to realize dense phase transportation.
compared with the positive pressure transportation, the energy consumption is higher under the same conditions.
