Audited Supplier
RAX
IP65
RoHS, ISO9001, CE
Infrared Water
Liquid
5 To100 C
Single Item
60mm
18
740
15A
250VAC
PPO
Water Flow Detection on Water Pipes
PPO;Fiber Glass
Ultimheat
9.1X3.2X17cm
Guangdongchina
8536500090
Product Description
Main uses: General application in flow detection. Recommended mounting position is on horizontal pipes, but can be mounted in any position. For water flow detection on dia 15 to 100mm water pipes. The built-in relay with SPDT contact can be used on resistive loads up to 15A 250V. The pilot light shows the contact position.
Functional principle:
Balanced magnetic paddle mounted perpendicular to the flow and activating a reed switch through the wall. The return of the paddle is made by magnetic action, without spring. No seal or liquid can pass between the piping system and the electrical contact. Suitable for corrosive water pools and spas and salination chlorination and bromination systems. Must not be used for water containing magnetic particles or high viscosity liquids, which block the movement of the paddle.
Adjustment:
- By cleaving the paddle- Fine adjustment by screw driver on internal dial (on models with connection box only)
Paddle shaft: Titanium, providing an outstanding corrosion resistance, and improved mechanical live. Suitable for corrosive water pools and spas and salination, chlorination and bromination systems.
Main housing material: PPO, fiber glass reinforced for improved pressure resistance, usable with potable water.
Paddle: PPO, 12 mm width, can be cleaved into 4 sections numbered 1 to 4 for pipe diameter adjustment.
Pipe mounting: Fiber glass reinforced union nut, ¾" BSPP, mounting on ¾" BSPP male fitting with gasket.
Recommended torque: 7±1Nm.
Gasket: NBR
Electrical rating: 15A, 250V, resistive load. Use on inductive circuits reduces electrical rating.
Electric contact type: SPDT
Liquid compatibility: For use with clean water and liquids without magnetic particles and without chemical
incompatibility with PPO and titanium.
Nominal pressure at 20°C: 1MPa (PN10)
Liquid temperature ranges: 5 to 100°C (cannot be used in water freezing pipes).
Ambient temperature range: 5 to 80°C
Ingress protection: IP65
Calibration tolerances: +/-15% (on paddle operating force at end of paddle 1).
Electrical connection: 2.5mm² connection block with screw terminals M16 cable gland output.
Installation instructions:
Paddle shaft: Titanium, providing an outstanding corrosion resistance, and improved mechanical live. Suitable for corrosive water pools and spas and salination, chlorination and bromination systems.
Main housing material: PPO, fiber glass reinforced for improved pressure resistance, usable with potable water.
Paddle: PPO, 12 mm width, can be cleaved into 4 sections numbered 1 to 4 for pipe diameter adjustment.
Pipe mounting: Fiber glass reinforced union nut, ¾" BSPP, mounting on ¾" BSPP male fitting with gasket.
Recommended torque: 7±1Nm.
Gasket: NBR
Electrical rating: 15A, 250V, resistive load. Use on inductive circuits reduces electrical rating.
Electric contact type: SPDT
Liquid compatibility: For use with clean water and liquids without magnetic particles and without chemical
incompatibility with PPO and titanium.
Nominal pressure at 20°C: 1MPa (PN10)
Liquid temperature ranges: 5 to 100°C (cannot be used in water freezing pipes).
Ambient temperature range: 5 to 80°C
Ingress protection: IP65
Calibration tolerances: +/-15% (on paddle operating force at end of paddle 1).
Electrical connection: 2.5mm² connection block with screw terminals M16 cable gland output.
Installation instructions:
- Check carefully the paddle orientation: The arrow on housing must be exactly parallel to the pipe.
- We recommend the use of nozzles of length below or equal to 18mm between the gasket seat and the inside of the tube and with an inner diameter above or equal to 13.5 mm, to avoid blocking of the paddle.
Accessories: ¾" male PVC saddles for DN40 to DN100 (OD) PVC pipes, and other fittings: see section 8 of this catalogue.
Options (MOQ apply): nickel plated ¾" BSPP union nut.
Important notice: In the case of plastic pipes (PVC, PE), the DN (nominal diameter) corresponds to the outside diameter and wall thickness is variable depending on the application. This must be taken into account to avoid blocking the paddle. In the case of metal pipes, the inner diameter corresponds to the DN. Flow values data are for tubes whose internal diameter corresponds to DN.
- We recommend the use of nozzles of length below or equal to 18mm between the gasket seat and the inside of the tube and with an inner diameter above or equal to 13.5 mm, to avoid blocking of the paddle.
Accessories: ¾" male PVC saddles for DN40 to DN100 (OD) PVC pipes, and other fittings: see section 8 of this catalogue.
Options (MOQ apply): nickel plated ¾" BSPP union nut.
Important notice: In the case of plastic pipes (PVC, PE), the DN (nominal diameter) corresponds to the outside diameter and wall thickness is variable depending on the application. This must be taken into account to avoid blocking the paddle. In the case of metal pipes, the inner diameter corresponds to the DN. Flow values data are for tubes whose internal diameter corresponds to DN.
Calibration (Calibration force ±15%, measured at end of paddle N°1) | |||||||
Low span end: 3gr | RAX636680G35N00C | ||||||
Middle span: 7gr | RAX676680G35N00C | ||||||
High span end: 14gr | RAX6E6680G35N00C | ||||||
JPCI Controls originated from the French family-owned company founded in 1972, our company was founded in 2000, headquartered in Gaoming District, Foshan City, Guangdong Province, China, which is specialized in the design and production of mechanical thermostats, safety devices and electric heating systems for domestic and industrial use. JPCI owns an internationally renowned brand, ULTIMHEAT, and has a subsidiary in Lyon, France.After more than 50 years of development, JPCI has become a research and development enterprise which is deeply exploring the international market.
JPCI Controls covers an area of 30,000 square meters, has more than 300 employees, including 30 professional R & D and laboratory employees, and produces more than 6 million products per year, with more than 10,000 product models. Our production has achieved full vertical integration to ensure quality control at each stage, our company has more than 1000 sets of testing equipment such as ultraviolet aging testing machine, motor loading machine, hydraulic hi-pot bursting testing machine to strictly monitor product quality.
JPCI Controls has always adhered to the values of innovation, listening, responding and continuous improvement to ensure that products can achieve the best quality. JPCI holds 250 patents and applies for an average of 20 patents per year. Won the national high-tech enterprises and passed the system certification ISO9001, ISO14001, ISO45001; It has a 750 self-built laboratory and has passed the ISO17025 laboratory certification of TUV&UL.
JPCI Controls is driven by innovation, guaranteed by quality, and takes environmental protection as its responsibilitylooking forward to working with you to create a better future.
