Audited Supplier
SPU-301
Black
Liquid
Polyurethane
Brush
Finish Coat
Moisture Cured
None Voc
Concrete
Solvent
Conversion Type
20 Kgs
Iron Drum
Yuhong/ OEM
Pail
No VOC
China
32089010
Product Description
Description
SPU-301H is a one component moisture-curing polyurethane waterproof coating especially used for horizontal plane. When this coating is applied on surface substrate, it has chemical reaction with the moisture in the air, and then it will form a seamless elastomeric rubber waterproof membrane.
Where to use
Undergrounds;
Parking garages;
Subways in open cut method;
Channels;
Kitchen or bathroom;
Floors, balcony and unexposed roofs;
Swimming pools, man-made fountain and other pools;
Top plate at plazas.
Advantages
Good tensile strength and elongation;
Both high and low temperature resistance;
Strong adhesive;
Seamless, no pinholes and bubbles;
Resistance to long-term water erosion;
Corrosion-resisting and mould-resisting;
Convenient to apply.
Standards
ASTM C 836
Packaging
SPU-301H is sealed in 20kg or 22.5kg pails and transported in wooden cases. Each wooden case can be contained 36 pails of SPU-301H.
Storage
SPU-301H material should be stored by sealed pails at dry and well-ventilated places and protected from sun or rain. The temperature in stored places can not be higher than 40° C. It can not be closed to fire sources. The normal shelf life is 6 months.
Transportation
SPU-301H is needed to be avoided sunshine and rain. Fire sources are forbidden during transportation.
Application System
Constructive System
The system is basically consisted of substrate, additional layer, waterproof coated membrane and protection layer.
Coverage
1.7kg per m2 gives dft 1mm minimum. Coverage may vary with the substrate condition during application.
Application Method
Surface preparation
Surfaces should be dry, stable, clean, smooth, without pockmarks or honeycombs and free from any dusts, oil or loose particles. Cracks and surface irregularities need to be filled by sealants and do additional waterproofing. For smooth and stable surfaces, this step can be skipped.
Additional layer
Paint SPU-301H as additional layer to enhance at internal and external corners, drain pipes, floor drains or embedded parts.
Application of waterproof coated membrane
It can use rubber scrapers or spray equipments to paint 2 or 3 times. After fully dry, it can be painted again. The normal time between each painting is 24 hour. The direction of second time painting needs to be perpendicular to the first time painting.
Application of protection layer
After waterproof coated membrane is fully dry and meets quality requirements, it can begin application of protection layer.
Notice
The temperature for application of SPU-301H should be above 5 ° C.
SPU-301H needs to be consumed instantly and can not be diluted with solvent.
The storage and application places should be well-ventilated and no fire.
SPU-301H is a one component moisture-curing polyurethane waterproof coating especially used for horizontal plane. When this coating is applied on surface substrate, it has chemical reaction with the moisture in the air, and then it will form a seamless elastomeric rubber waterproof membrane.
Where to use
Undergrounds;
Parking garages;
Subways in open cut method;
Channels;
Kitchen or bathroom;
Floors, balcony and unexposed roofs;
Swimming pools, man-made fountain and other pools;
Top plate at plazas.
Advantages
Good tensile strength and elongation;
Both high and low temperature resistance;
Strong adhesive;
Seamless, no pinholes and bubbles;
Resistance to long-term water erosion;
Corrosion-resisting and mould-resisting;
Convenient to apply.
Standards
ASTM C 836
Packaging
SPU-301H is sealed in 20kg or 22.5kg pails and transported in wooden cases. Each wooden case can be contained 36 pails of SPU-301H.
Storage
SPU-301H material should be stored by sealed pails at dry and well-ventilated places and protected from sun or rain. The temperature in stored places can not be higher than 40° C. It can not be closed to fire sources. The normal shelf life is 6 months.
Transportation
SPU-301H is needed to be avoided sunshine and rain. Fire sources are forbidden during transportation.
Application System
Constructive System
The system is basically consisted of substrate, additional layer, waterproof coated membrane and protection layer.
Coverage
1.7kg per m2 gives dft 1mm minimum. Coverage may vary with the substrate condition during application.
Application Method
Surface preparation
Surfaces should be dry, stable, clean, smooth, without pockmarks or honeycombs and free from any dusts, oil or loose particles. Cracks and surface irregularities need to be filled by sealants and do additional waterproofing. For smooth and stable surfaces, this step can be skipped.
Additional layer
Paint SPU-301H as additional layer to enhance at internal and external corners, drain pipes, floor drains or embedded parts.
Application of waterproof coated membrane
It can use rubber scrapers or spray equipments to paint 2 or 3 times. After fully dry, it can be painted again. The normal time between each painting is 24 hour. The direction of second time painting needs to be perpendicular to the first time painting.
Application of protection layer
After waterproof coated membrane is fully dry and meets quality requirements, it can begin application of protection layer.
Notice
The temperature for application of SPU-301H should be above 5 ° C.
SPU-301H needs to be consumed instantly and can not be diluted with solvent.
The storage and application places should be well-ventilated and no fire.
| Item | Requirement | Test Method |
| Hardness | ≥50 | ASTM D 2240 |
| Weight Loss | ≤20% | ASTM C 1250 |
| Low temperature crack bridging | No cracking | ASTM C 1305 |
| Film thickness(vertical surface) | 1.5mm±0.1mm | ASTM C 836 |
| Adhesion-in-peel after water immersion | 175N/m | ASTM C 794 |
| Optional test after adhesion in peel | No separation at surface | ASTM C 836 |
| Extensibility after hear aging | 6.4mm (note 1) no cracking | ASTM C 1522 |
| Stability | ≥6 months | ASTM C 836 |
