Audited Supplier
Phone Remote Control Relay Module
WiFi Module
AP+STA
External
151-200Mbps
3.3V
18dBi
Blue
WiFi Module
CE
Other
Other
Other
kozhiyou
Electrostatic Bag Packaging
Shenzhen
Product Description
Sinilink WIFI mobile phone remote control relay module DC6V~36V smart home phone APP ESP-12F XY-WF36V
product qualitybrand new
REMIND
1 . If you use the charger Pal for power supply , please make sure that the chargerPal is always on . Many charger Pal with low current will automatically turn off theoutput and cannot be used . Standby power consumption of this product is about0 . 5W 5V100MA2 . Wifi hotspot can only connect to 2 . 4g frequency . Some routes are connected to5G and 2 . 4g3 . All power off Settings can be saved , and will be connected automatically afterpower onIf the wifi hotspot name or password has changed , it needs to be resetSituations where routes or products need to be restarted to linkIf you encounter this problem , you can replace the WIF hotspot and router4 . It will not work normally after being disconnected from the Internet . WIF is requiredto connect to the Internet all the timeThe network can be automatically connected5 . It is recommended to use a router with stable performance . Otherwise , you mayencounter unpredictable problems for a long time , such as failure of the linkFunction description As long as WF is constant and the phone has a network , theswitch can be controlled by APP whenever and wherever6 . For some poor routers , the connection may drop for a long time . If the router canbe restarted and work normally , it is the problem of the router( If this is the case , you can find another router to test )
Features:
1: Widely used
2: The system built with advanced architecture technology supports the concurrency of tens of millions of users. The system is stable and fast!
3: Timing / delay / cycle / self-locking / sharing
4: Support tmall elf and small voice. Support remote firmware upgrade
5: Convenient and convenient
Networking steps:
Step 1:During the pairing process, the WiFi network must be 2.4G, and the 5g network cannot be paired. (if your WiFi router 2.4G and 5g are combined networks, please reconfigure the router, separate them, and select the 2.4G network)
Step 2:When the product is powered on, it enters touch pairing mode by default.
Step 3 Click "start connection""
Touch mode: the blue light flashes rapidly for 3 times continuously, wait for 1 second, and flash quickly for 3 times again
So back and forth.
AP mode: the blue light flashes continuously and quickly.
Note: after the product is powered on, it will enter touch pairing mode by default. If pairing fails, Please follow the prompts of app.
Package Include:
1 * controller module
product qualitybrand new
| color | as show |
REMIND
1 . If you use the charger Pal for power supply , please make sure that the chargerPal is always on . Many charger Pal with low current will automatically turn off theoutput and cannot be used . Standby power consumption of this product is about0 . 5W 5V100MA2 . Wifi hotspot can only connect to 2 . 4g frequency . Some routes are connected to5G and 2 . 4g3 . All power off Settings can be saved , and will be connected automatically afterpower onIf the wifi hotspot name or password has changed , it needs to be resetSituations where routes or products need to be restarted to linkIf you encounter this problem , you can replace the WIF hotspot and router4 . It will not work normally after being disconnected from the Internet . WIF is requiredto connect to the Internet all the timeThe network can be automatically connected5 . It is recommended to use a router with stable performance . Otherwise , you mayencounter unpredictable problems for a long time , such as failure of the linkFunction description As long as WF is constant and the phone has a network , theswitch can be controlled by APP whenever and wherever6 . For some poor routers , the connection may drop for a long time . If the router canbe restarted and work normally , it is the problem of the router( If this is the case , you can find another router to test )
Features:
1: Widely used
2: The system built with advanced architecture technology supports the concurrency of tens of millions of users. The system is stable and fast!
3: Timing / delay / cycle / self-locking / sharing
4: Support tmall elf and small voice. Support remote firmware upgrade
5: Convenient and convenient
Networking steps:
Step 1:During the pairing process, the WiFi network must be 2.4G, and the 5g network cannot be paired. (if your WiFi router 2.4G and 5g are combined networks, please reconfigure the router, separate them, and select the 2.4G network)
Step 2:When the product is powered on, it enters touch pairing mode by default.
Step 3 Click "start connection""
Touch mode: the blue light flashes rapidly for 3 times continuously, wait for 1 second, and flash quickly for 3 times again
So back and forth.
AP mode: the blue light flashes continuously and quickly.
Note: after the product is powered on, it will enter touch pairing mode by default. If pairing fails, Please follow the prompts of app.
Package Include:
1 * controller module
