Audited Supplier
SHIHM-160W-240V
Ce, SAA
0.3 to 0.5m
80W to 250W/Square Meter
12 V to 240V
Heat
Heating Mat
PVC or FEP Coated
Conduct Heat
Senphus
Senphus
Carton, Spool
SGS
Jiangsu, China (Mainland)
85168000
Product Description
Tile FLoor Heater UL Approved E481865
Heating mat is a good floor heating system. It is easy to install and is suitable for various floor decorative materials, whether it is concrete floor and wood flooring, or the old tiles floor or terrazzo floor. It is installed in the tile adhesives and almost doesn't affect the floor elevation. Anze heating mat can be directly laid on the original floor without any treatment to the original floor. Meanwhile, the thin preheat layer can offer you the desired floor temperature 20-30 minutes after the system is activated. Therefore the fast heating system is the best choice for rooms such as bathroom. It is applicable to the overall heating, comfort heating, wall heating, strict demands of floor height and renovation.
Floor Heating System Specification
Floor Heating Systems Installation Guide
1.Divide the floor into a series of rectangles. From these measurements you can calculate how many mats you'll need and what sizes. Exclude permanent or static fixtures from your calculations. If the floor is self-levelling compound over concrete.
2.Lay the first run. At the end of the run cut the mat leaving the cable intact, turn the mat through 90 or 180 degrees and continue laying. When the area is covered, adjust the mat until the loops are equal distance apart. Now stick the mat to the sub floor using the special tape bands.
3.Lay the temperature probe from the programmable thermostat onto the floor centered between two of the cable loops and secure it to the floor surface. Now take the unheated power lead from the end of the matting system which should be positioned near the thermostat. Refer to the installation manual for testing instructions and readings.
4.Either lay a thin, self-levelling compound over the mat and leave it to dry before laying tiles or trowel flexible tile adhesive directly over the mat and lay the floor tiles. Once the grouting is complete let the tile adhesive cure before switching on the system.
Heating mat is a good floor heating system. It is easy to install and is suitable for various floor decorative materials, whether it is concrete floor and wood flooring, or the old tiles floor or terrazzo floor. It is installed in the tile adhesives and almost doesn't affect the floor elevation. Anze heating mat can be directly laid on the original floor without any treatment to the original floor. Meanwhile, the thin preheat layer can offer you the desired floor temperature 20-30 minutes after the system is activated. Therefore the fast heating system is the best choice for rooms such as bathroom. It is applicable to the overall heating, comfort heating, wall heating, strict demands of floor height and renovation.
Floor Heating System Specification
| Model | V | W | Ohm | M2 |
| SHIHM-160-1.0M2 | 240 | 160 | 360.0 | 1 |
| SHIHM-160-1.5M2 | 240 | 240 | 240.0 | 1.5 |
| SHIHM-160-2.0M2 | 240 | 320 | 180.0 | 2 |
| SHIHM-160-2.5M2 | 240 | 400 | 144.0 | 2.5 |
| SHIHM-160-3.0M2 | 240 | 480 | 120.0 | 3 |
| SHIHM-160-3.5M2 | 240 | 560 | 102.9 | 3.5 |
| SHIHM-160-4.0M2 | 240 | 640 | 90.0 | 4 |
| SHIHM-160-5.0M2 | 240 | 800 | 72.0 | 5 |
| SHIHM-160-6.0M2 | 240 | 960 | 60.0 | 6 |
| SHIHM-160-7.0M2 | 240 | 1120 | 51.4 | 7 |
| SHIHM-160-8.0M2 | 240 | 1280 | 45.0 | 8 |
| SHIHM-160-10.0M2 | 240 | 1600 | 36.0 | 10 |
Floor Heating Systems Installation Guide
1.Divide the floor into a series of rectangles. From these measurements you can calculate how many mats you'll need and what sizes. Exclude permanent or static fixtures from your calculations. If the floor is self-levelling compound over concrete.
2.Lay the first run. At the end of the run cut the mat leaving the cable intact, turn the mat through 90 or 180 degrees and continue laying. When the area is covered, adjust the mat until the loops are equal distance apart. Now stick the mat to the sub floor using the special tape bands.
3.Lay the temperature probe from the programmable thermostat onto the floor centered between two of the cable loops and secure it to the floor surface. Now take the unheated power lead from the end of the matting system which should be positioned near the thermostat. Refer to the installation manual for testing instructions and readings.
4.Either lay a thin, self-levelling compound over the mat and leave it to dry before laying tiles or trowel flexible tile adhesive directly over the mat and lay the floor tiles. Once the grouting is complete let the tile adhesive cure before switching on the system.
