Audited Supplier
VESA6H
by Nidec Embraco
18 Months
Lubricated
Air Cooling
Single Cylinder
Horizontal
Closed Type
Single-Stage
R600a
230V
40-150Hz
6.23
Embraco
by Negotiation
9.04 cc
China
84143011
Product Description
COMPRESSOR DEFINITION
Designation VEM T9C
Nominal Voltage/Frequency 230 V 40-150 Hz
Engineering Number 513906128
A - APPLICATION / LIMIT WORKING CONDITIONS
1 Type Hermetic reciprocating compressor
2 Refrigerant R-600a
3 Nominal voltage and frequency 230 / 40-150 [ V / Hz ]
4 Application type Low Back Pressure
4.1 Evaporating temperature range -35°C to -10°C (-31°F to 14°F)
5 Motor type BPM
6 Starting torque LST - Low Starting Torque
7 Expantion device Capillary tube
8 Compressor cooling Operating voltage range
50 Hz 60 Hz
8.1 LBP (32ºC Ambient temperature) Static 187 to 255 V -
8.2 LBP (43ºC Ambient temperature) Static 187 to 255 V -
8.3 HBP (32ºC Ambient temperature) - - -
8.4 HBP (43ºC Ambient temperature) - - -
9 Maximum condensing temperature
9.1 Operating (gauge) 6.9 [kgf/cm²] (98 psig) / ºC - ºF
9.2 Peak (gauge) 7.8 [kgf/cm²] (111 psig) / ºC - ºF
10 Maximum winding temperature 130 [ °C ]
B - MECHANICAL DATA
1 Commercial designation [hp]
2 Displacement 9.04 [cm³] (0.552 cu.in)
2.1 Bore [mm] 24.000
2.2 Stroke [mm] 20.000
3 Lubricant charge 210 [ml] (7.10 fl.oz.)
3.1 Lubricants approved
3.2 Lubricants type/viscosity ALQUILB / ISO5
4 Weight (with oil charge) 6.73 [kg] (14.84 lb.)
5 Nitrogen charge - [kgf/cm²]
C - ELETRICAL DATA
1 Nominal Voltage/Frequency/Number of Phases 230 V 40-150 Hz 3~ (Three phase)
2 Starting device type Inverter
2.1 Starting device VCC32456XXXX
3 Start capacitor - [µF(VAC minimum)]
4 Run capacitor - [µF(VAC minimum)]
5 Motor protection VCC32456XXXXX
6 Start winding resistance [Wat 25ºC (77ºF)] +/- 8%
7 Run winding resistance [Wat 25ºC (77ºF)] +/- 8%
8 LRA - Locked rotor amperage (40/150 Hz) - [A] - Measured according to UL 984
9 FLA - Full load amperage L/MBP (40/150 Hz) - [A] - Measured according to UL 984
10 FLA - Full Load Amperage HBP (40/150 Hz) - [A] - Measured according to UL 984
11 Approval boards certification
D - PERFORMANCE - CHECK POINT DATA
| TEST CONDITIONS: ASHRAELBP32 Evaporating temperature -23.3°C (-9.94°F) @220V1200RPM Static (Condensing temperature 54.4°C (129.92°F)) | ||||||||
| Cooling capacity +/- 5% | Power consumption +/- 5% | Current consumption +/- 5% | Gas flow rate +/- 5% | EFFICIENCY RATE +/- 7% | ||||
| [Btu/h] | [kcal/h] | [W] | [W] | [A] | [kg/h] | [Btu/Wh] | [kcal/Wh] | [W/W] |
| 209 | 53 | 61 | 39 | 0.31 | 0.66 | 5.36 | 1.35 | 1.57 |
| TEST CONDITIONS: ASHRAELBP32 Evaporating temperature -23.3°C (-9.94°F) @220V1600RPM Static (Condensing temperature 54.4°C (129.92°F)) | ||||||||
| Cooling capacity +/- 5% | Power consumption +/- 5% | Current consumption +/- 5% | Gas flow rate +/- 5% | EFFICIENCY RATE +/- 7% | ||||
| [Btu/h] | [kcal/h] | [W] | [W] | [A] | [kg/h] | [Btu/Wh] | [kcal/Wh] | [W/W] |
| 287 | 72 | 84 | 49 | 0.39 | 0.90 | 5.86 | 1.48 | 1.72 |
| TEST CONDITIONS: ASHRAELBP32 Evaporating temperature -23.3°C (-9.94°F) @220V2000RPM Static (Condensing temperature 54.4°C (129.92°F)) | ||||||||
| Cooling capacity +/- 5% | Power consumption +/- 5% | Current consumption +/- 5% | Gas flow rate +/- 5% | EFFICIENCY RATE +/- 7% | ||||
| [Btu/h] | [kcal/h] | [W] | [W] | [A] | [kg/h] | [Btu/Wh] | [kcal/Wh] | [W/W] |
| 364 | 92 | 107 | 61 | 0.48 | 1.14 | 5.97 | 1.50 | 1.75 |
| TEST CONDITIONS: ASHRAELBP32 Evaporating temperature -23.3°C (-9.94°F) @220V3000RPM Static (Condensing temperature 54.4°C (129.92°F)) | ||||||||
| Cooling capacity +/- 5% | Power consumption +/- 5% | Current consumption +/- 5% | Gas flow rate +/- 5% | EFFICIENCY RATE +/- 7% | ||||
| [Btu/h] | [kcal/h] | [W] | [W] | [A] | [kg/h] | [Btu/Wh] | [kcal/Wh] | [W/W] |
| 527 | 133 | 154 | 87 | 0.68 | 1.65 | 6.06 | 1.53 | 1.78 |
| TEST CONDITIONS: ASHRAELBP32 Evaporating temperature -23.3°C (-9.94°F) @220V4500RPM Static (Condensing temperature 54.4°C (129.92°F)) | ||||||||
| Cooling capacity +/- 5% | Power consumption +/- 5% | Current consumption +/- 5% | Gas flow rate +/- 5% | EFFICIENCY RATE +/- 7% | ||||
| [Btu/h] | [kcal/h] | [W] | [W] | [A] | [kg/h] | [Btu/Wh] | [kcal/Wh] | [W/W] |
| 731 | 184 | 214 | 126 | 0.98 | 2.30 | 5.80 | 1.46 | 1.70 |
E - PERFORMANCE - CURVES
| TEST CONDITIONS: ASHRAE32 (Condensing temperature 35ºC (+95ºF) ) @220V1200RPM Static | ||||||||||
| Evaporating temperature | Cooling capacity +/- 5% | Power consumption +/- 5% | Current consumption +/- 5% | Gas flow rate +/- 5% | EFFICIENCY RATE +/- 7% | |||||
| °C | (°F) | [Btu/h] | [kcal/h] | [W] | [W] | [A] | [kg/h] | [Btu/Wh] | [kcal/Wh] | [W/W] |
| -35 | (-31) | 96 | 24 | 28 | 18 | 0.18 | 0.30 | 5.02 | 1.27 | 1.47 |
| -30 | (-22) | 186 | 47 | 54 | 29 | 0.26 | 0.58 | 7.02 | 1.77 | 2.06 |
| -25 | (-13) | 269 | 68 | 79 | 36 | 0.32 | 0.84 | 8.45 | 2.13 | 2.48 |
| -20 | (- 4) | 340 | 86 | 100 | 40 | 0.34 | 1.07 | 9.39 | 2.37 | 2.75 |
| -15 | (+ 5) | 394 | 99 | 115 | 41 | 0.35 | 1.24 | 9.92 | 2.50 | 2.91 |
| -10 | (+14) | 424 | 107 | 124 | 41 | 0.34 | 1.34 | 10.13 | 2.55 | 2.97 |
| TEST CONDITIONS: ASHRAE32 (Condensing temperature 45ºC (+113ºF) ) @220V1200RPM Static | ||||||||||
| Evaporating temperature | Cooling capacity +/- 5% | Power consumption +/- 5% | Current consumption +/- 5% | Gas flow rate +/- 5% | EFFICIENCY RATE +/- 7% | |||||
| °C | (°F) | [Btu/h] | [kcal/h] | [W] | [W] | [A] | [kg/h] | [Btu/Wh] | [kcal/Wh] | [W/W] |
| -35 | (-31) | 161 | 41 | 47 | 28 | 0.25 | 0.51 | 6.00 | 1.51 | 1.76 |
| -30 | (-22) | 198 | 50 | 58 | 34 | 0.29 | 0.62 | 6.59 | 1.66 | 1.93 |
| -25 | (-13) | 222 | 56 | 65 | 35 | 0.30 | 0.70 | 6.56 | 1.65 | 1.92 |
| -20 | (- 4) | 229 | 58 | 67 | 33 | 0.27 | 0.72 | 5.99 | 1.51 | 1.75 |
| -15 | (+ 5) | 213 | 54 | 62 | 27 | 0.22 | 0.67 | 4.96 | 1.25 | 1.45 |
| -10 | (+14) | 169 | 42 | 49 | 20 | 0.16 | 0.53 | 3.57 | 0.90 | 1.05 |
| TEST CONDITIONS: ASHRAE32 (Condensing temperature 55ºC (+131ºF) ) @220V1200RPM Static | ||||||||||
| Evaporating temperature | Cooling capacity +/- 5% | Power consumption +/- 5% | Current consumption +/- 5% | Gas flow rate +/- 5% | EFFICIENCY RATE +/- 7% | |||||
| °C | (°F) | [Btu/h] | [kcal/h] | [W] | [W] | [A] | [kg/h] | [Btu/Wh] | [kcal/Wh] | [W/W] |
| -35 | (-31) | 97 | 24 | 28 | 24 | 0.22 | 0.30 | 4.23 | 1.07 | 1.24 |
| -30 | (-22) | 132 | 33 | 39 | 28 | 0.25 | 0.42 | 4.70 | 1.19 | 1.38 |
| -25 | (-13) | 151 | 38 | 44 | 28 | 0.24 | 0.47 | 4.51 | 1.14 | 1.32 |
| -20 | (- 4) | 146 | 37 | 43 | 23 | 0.19 | 0.46 | 3.74 | 0.94 | 1.09 |
| -15 | (+ 5) | 113 | 29 | 33 | 15 | 0.12 | 0.36 | 2.46 | 0.62 | 0.72 |
| -10 | (+14) | 46 | 12 | 14 | 5 | 0.04 | 0.15 | 0.76 | 0.19 | 0.22 |
| F - EXTERNAL CHARACTERISTICS | ||||
| 1 Base plate | European Standard EUEM | |||
| 2 Tray holder | No | |||
| 3 Connectors | ||||
| 3.1 SUCTION | 6.2 +0.05/+0.05 | [mm] | (0.244" | +0.002"/+0.002") |
| 3.1.1 Material | Copper | |||
| 3.1.2 Shape | Slanted 40° up + 0° to Back | |||
| 3.2 DISCHARGE | 4.9 +0.10/-0.05 | [mm] | (0.193" | +0.004"/-0.002") |
| 3.2.1 Material | Copper | |||
| 3.2.2 Shape | Slanted 42° up + 24° to Back | |||
| 3.3 PROCESS | 6.2 +0.05/+0.05 | [mm] | (0.244" | +0.002"/+0.002") |
| 3.3.1 Material | Copper | |||
| 3.3.2 Shape | Slanted 42º up + 45° to Back | |||
| 3.4 Oil cooler (Copper) | No | [mm] | ||
| 3.5 Connector sealing | Rubber Plugs | |||
| Series | Comp. Model | Displacement | Speed | Capacity | COP | Oil Viscosity | Certification | Height |
| (cm3) | rpm | W | W/W | |||||
| VEMT | VEMT7C | 7.23 | 1600 | 68.0 | 1.66 | ISO5 | CCC | 166 |
| 2000 | 79.0 | 1.70 | ||||||
| 3000 | 117.0 | 1.74 | ||||||
| 4500 | 173.0 | 1.7 | ||||||
| VEMT | VEMT9C | 9.04 | 1600 | 88.0 | 1.68 | ISO5 | CCC | 166 |
| 2000 | 106.0 | 1.74 | ||||||
| 3000 | 154.0 | 1.76 | ||||||
| 4500 | 211.0 | 1.63 | ||||||
| VEMT | VEMT11C | 11.14 | 1600 | 106.0 | 1.82 | ISO5 | CCC | 166 |
| 2000 | 133.0 | 1.85 | ||||||
| 3000 | 196.0 | 1.85 | ||||||
| 4500 | 265.0 | 1.67 | ||||||
| VEMT | VEMT9C | 9.04 | 1200 | 62.0 | 1.65 | ISO5 | CCC | 166 |
| 1600 | 84.0 | 1.72 | ||||||
| 2000 | 106.0 | 1.74 | ||||||
| 3000 | 150.0 | 1.76 | ||||||
| 4500 | 203.0 | 1.66 | ||||||
| VEMT | VEMT11C | 9.04 | 1200 | 77.0 | 1.52 | ISO5 | CCC | 166 |
| 1600 | 105.0 | 1.65 | ||||||
| 2000 | 133.0 | 1.72 | ||||||
| 3000 | 198.0 | 1.76 | ||||||
| 4500 | 272.0 | 1.58 | ||||||
| VEMX | VEMX9C+ | 9.04 | @1200 | 61.3 | 1.75 | ISO5 | CCC/VDE | 166 |
| @1600 | 83.8 | 1.87 | ||||||
| @2000 | 106.6 | 1.90 | ||||||
| @3000 | 156.3 | 1.87 | ||||||
| @MAX SPEED(ref.4450) | 223.6 | 1.73 | ||||||
| VEMY | VEMY9C | 9.04 | @1600 | 85.0 | 1.74 | ISO5 | CCC/VDE | 158 |
| @2000 | 106.0 | 1.74 | ||||||
| @3000 | 161.0 | 1.78 | ||||||
| @MAX SPEED(ref.4500) | 220.0 | 1.70 | ||||||
| VEMB | VEMB9C | 9.04 | @1200 | 64.0 | 1.74 | ISO5 | CCC/VDE | 166 |
| @1600 | 85.0 | 1.85 | ||||||
| @2000 | 106.0 | 1.90 | ||||||
| @3000 | 161.0 | 1.87 | ||||||
| @MAX SPEED(ref.4100) | 203.0 | 1.76 | ||||||
| VEMB11C | 11.14 | @1600 | 108.0 | 1.85 | ISO5 | CCC/VDE | 166 | |
| @2000 | 135.0 | 1.90 | ||||||
| @3000 | 205.0 | 1.90 | ||||||
| @MAX SPEED(ref.4300) | 282.0 | 1.75 | ||||||
| VEMC | VEMC5C | 5.19 | @1200 | 30.6 | 1.57 | ISO5 | CCC/VDE | 166 |
| @1600 | 42.3 | 1.75 | ||||||
| @2000 | 53.2 | 1.79 | ||||||
| @3000 | 78.1 | 1.81 | ||||||
| @MAX SPEED(ref.4350) | 117.9 | 1.77 | ||||||
| VEMC7C | 7.23 | @1200 | 45.4 | 1.74 | ISO5 | CCC/VDE | 166 | |
| @1600 | 63.0 | 1.87 | ||||||
| @2000 | 80.4 | 1.89 | ||||||
| @3000 | 116.0 | 1.87 | ||||||
| @MAX SPEED(ref.4250) | 167.9 | 1.82 | ||||||
| VEMC9C | 9.04 | @1200 | 62.3 | 1.89 | ISO5 | CCC/VDE | 166 | |
| @1600 | 85.4 | 1.94 | ||||||
| @2000 | 107.3 | 1.95 | ||||||
| @3000 | 159.1 | 1.96 | ||||||
| @MAX SPEED(ref.4450) | 221.6 | 1.81 | ||||||
| Test Condition -23.3/54.4/32.2ºC |
