Tl Series Vertical High-Voltage Synchronous Motor

This series motors conform to JB/T8667.2-1997 "large TL series three-phase synchronous motor technology conditions" and GB/T755 the basic technical requirements for rotating machine.
This series three-phase vertical synchronous motor is mainly used for driving vertical axial flow, mixed flow pump, the design adopts domestic and international advanced technical standards, and absorbs the advanced ideas of this kind of motor technology at home and abroad, combined with our company for this series motors are long-term experience in design development and production and manufacturing, with high efficiency, little vibration, reliable operation, installation and easy maintenance.Has in irrigation and drainage system, the yellow jiqing, such as the south-north water diversion project has been successfully used in.
Motor installed in the pump on the basis of the above, through the shaft end flange to the pump rigid connection, frame show room on the ground, the remaining within the pit under the ground.On the motor structure of two guide trailer, rack with thrust bearing, and guide bearing, only guide bearing within a frame.From top to bottom in oil pools are frame, bearing for self lubricating oil bath.On the rack mounted on the stator, the stator to the next rack, the rack is located on the basis of.Axial force of the motor weight, from the pump and mechanical ten-fold increase, through the frame is passed on to the base.

Product parameters:
Power range: 500 ~ 10000 kw;
Nominal voltage 3 kv and 6 kv, 10 kv and special voltage level;
Stand no. : 1730, 2150, 2600, 3250, 3700, 5500;
The number of: 12 ~ 60;
Phase number: 3;
Speed: 100 ~ 500 r/min;
Rated frequency 50 hz, 60 hz, etc.
Protection grade: IP21, IP23, etc;
Insulation level: F/F;
Cooling mode: IC27, IC01, etc;
Installation method: IM8425 etc.
The motor rated power factor of 0.9 (advanced);
Loss of motor torque and the guarantee of the ratio of the rated torque value not less than 1.5;
Full voltage starting, the locked-rotor torque of the motor and the guarantee of the ratio of the rated torque value not less than 0.45;
Full voltage starting, the nominal pull in torque of the motor and the guarantee of the ratio of the rated torque value not less than 1.0;
Full voltage start, turn the wall of the motor current and the guarantee of the ratio of the rated current value is not greater than 6.0;
Electric function under 120% of the rated speed, 2 min overspeed test without harmful deformation.

TDL large vertical hydraulic engineering motor is optimized and designed with new materials and new technology to meet the relevant requirements of users. It has reliable performance, low temperature rise, low loss, high efficiency, excellent manufacturing, low vibration, large starting torque and structure. Simple and easy to maintain.


Packing and shipping:
1. The outer packaging of the products are all standard export-oriented wooden plywood packaging.
2, the product packaging is protected by moisture, water plastic soft packaging
3. For products with special transportation requirements (such as temperature, fragile, variability, and easy to get wet), the packaging protection measures will be strengthened, and the target mark will be printed on the package.
4. There are obvious signs and symbols on the packing box that must be paid attention to during transportation and storage (such as position, moisture, rain, shockproof, lifting position, etc.).


Our company's motor manufacturing factory adheres to the concept of green, efficient and energy-saving production service, pays attention to the harmonious development of internal and external environment, builds environmentally friendly motor manufacturing enterprises, strictly implements motor standard process, and selects high-quality energy-saving materials to ensure the quality of motor products.


The company insists on providing high-quality motor products and services to users, and has won high praise from many domestic and foreign customers. The company will receive many foreign merchants to visit our factory every year, and establish a good cooperative relationship through on-site inspection of our factory. Our company always welcomes customers to visit our factory.


More details, welcome to call us!
Q: What are the payment terms?
A: 30% T/T in advance, 70% before shipment
Q: What is your delivery time?
A: Different models with different time, 10-90 days after order confirmed.
Q: What is your MOQ?
A: It depends on model.
Q: Where is your loading port?
A: Shanghai or Tianjing Port, China.