The heating modes concludes electric heating of jacket and coil heating. Featuring reasonable structure, advanced technology, durability, simple operation and convenient use, it is regarded as an ideal chemical device that can invest little, put into production quickly and gain high interest. It can realize the charging control, discharging control, stirring control and manual and automatic control during the mixing.


A stainless steel tank is equipped with various accessories used for various purposes in order to satisfy different technological requirements or the needs of the tank's own structure. For example, it is required to install the jacket outside the tank or coilers inside the tank to provide or remove the reaction heat because the heat effect always accompanies with the material during the reaction process. In order to connect the speed reducer and the shaft seal, a base should be welded on a head cover; in order to overhaul the internal components, feed and discharge easily, manholes, handholes and various tubes should be installed and welded; in order to observe and control material's temperature, pressure and liquid height efficiently, the thermometer, pressure gauge, level gauge, sight glass and relief devices should be installed. Sometimes in order to change the flow pattern of the material, increase the mixing intensity, strengthen the mass transfer and heat transfer, it is required to install the baffle and draft tube.


- Check whether there is any serious damage and deformation of device during the transportation, and whether the fasteners is loose.
- Adopt the method of embedded anchor bolt to install the device horizontally on a firm foundation.
- Please install the device, electrical control device and accessories correctly under the guidance of professionals. Check whether the pipelines are unblocked, whether the installed device is correct, and whether there is damage. Before starting the device, please check whether there are people or objects around, inside and outside the device affecting the normal operation, so as to avoid danger.
- Please carry out the trial operation first for a few seconds after the installation. It can not be done until there is no electrical short circuit or abnormal sound.
- If a mixing tank is equipped with the mechanical seal, add moderate amount of 10# oil or sewing-machine oil into the lubricating grooves of the mechanical seal before starting the main engine. The coolant should be supplied into the cooling chamber of the mechanical seal so that the mechanical seal can be well lubricated and cooled. The mechanical seal is not adjusted when leaving the factory. After installation, the mechanical seal should be adjusted to the optimal position according to the installation instructions before normal operation. (according to the needs of users).
- Please check the bearing temperature, running smoothness, tightness, as well as the condition of meters when the device is in normal operation. The material can not be put into operation until it is confirmed that everything is normal.

- Check whether there is any serious damage and deformation of device during the transportation, and whether the fasteners is loose.
- Adopt the method of embedded anchor bolt to install the device horizontally on a firm foundation.
- Please install the device, electrical control device and accessories correctly under the guidance of professionals. Check whether the pipelines are unblocked, whether the installed device is correct, and whether there is damage. Before starting the device, please check whether there are people or objects around, inside and outside the device affecting the normal operation, so as to avoid danger.
- Please carry out the trial operation first for a few seconds after the installation. It can not be done until there is no electrical short circuit or abnormal sound.
- If a mixing tank is equipped with the mechanical seal, add moderate amount of 10# oil or sewing-machine oil into the lubricating grooves of the mechanical seal before starting the main engine. The coolant should be supplied into the cooling chamber of the mechanical seal so that the mechanical seal can be well lubricated and cooled. The mechanical seal is not adjusted when leaving the factory. After installation, the mechanical seal should be adjusted to the optimal position according to the installation instructions before normal operation. (according to the needs of users).
- Please check the bearing temperature, running smoothness, tightness, as well as the condition of meters when the device is in normal operation. The material can not be put into operation until it is confirmed that everything is normal.

- How long is the delivery period of one unit?
- What specification does the device have?
- What material does the device use?
- Can the device with a jacket be provided?
- What is the applicable temperature?
- What is the design pressure?


- According to product' s using condition, technicians will offer rationalization proposals to assist clients to select proper product types;
- Provide detailed product performance specification;
- Provide professional quotation information;
- Provide 24-hour technical consultation and reply.
In-Sale Service:
- With supervision from the source of products, the qualified rate of raw materials entering the factory can reach 100%;
- Whole manufacturing process are in strict accordance with promised procedure requirements, product qualified rate can reach 100%;
- Provide product's inspection record of key junctures to customers;
- Provide production schedule photos to customers at regular intervals;
- Package and transport of products are in strict accordance with the export standard.
After-Sale Service:
- Under the premise of correct installation, normal maintenance and using, we guarantee one-year warranty period;
- When warranty period has expired, our sold products enjoys lifetime guarantee repair, we only charge cost price for changing product's standard component and sealing component;
- During installation and adjustment period, our after-sale service staff will communicate with customers frequently to know product's running state in time. Assist customers to install and adjust products until customers are satisfied.