Audited Supplier
IR-B steel pipe
Seamless
Cold Rolled and Hot Rolled
Alloy Steel
Bare Pipe
Machinery Industry, Chemical Industry, Special Purpose
Round
20mm~114mm
1mm~8mm
Fixed Length, by Random
Bare Pipe, Anti-Rust Painting
Plain Ends, Bevel Ends with End Caps
Iron&steel
Standard Seaworthy Packing
ASME
China
73045910
Product Description
Outer diameter: 20mm~114mm
Wall thickness: 1mm~10mm
Length: 6meters, 12meters, by random
Specifications of ma}or steel:
10,20,20G,20MnG,25MnG,15CrMoG,12Cr2MoG,12Cr1MoVG,12Cr2MoWVTiB,10Cr9Mo1VNb,SA210A1,SA210C,SA213 T11,SA213 T12,SA213 T22,SA213 T23,SA213 T91,SA213 T92,ST45.8/III,15Mo3,13CrMo44,10CrMo910etc.
Small Calibers Seamless steel tubes for high(low and medium) pressure boilers and petrochemical industry
Standards:
ASME SA 179,
ASME SA 192
DINl7175 Deutsches industrial standard~
Application:
Used as the pipes on the heated side of low and medium pressure boilers(normally with operating pressure not higher than 5.88Mpa and
operating temperature below 450 oc);as the pipes on the heated sides of high·pressure boilers,economizers,overheaters,reheaters and pipes
for petrochemical industry(with the operating pressure above 9.8Mpa and operating temperature ranging between 450~C~650~C1
Diamensional tolerances:
Mechanical properties:
Chemical composition:
Wall thickness: 1mm~10mm
Length: 6meters, 12meters, by random
Specifications of ma}or steel:
10,20,20G,20MnG,25MnG,15CrMoG,12Cr2MoG,12Cr1MoVG,12Cr2MoWVTiB,10Cr9Mo1VNb,SA210A1,SA210C,SA213 T11,SA213 T12,SA213 T22,SA213 T23,SA213 T91,SA213 T92,ST45.8/III,15Mo3,13CrMo44,10CrMo910etc.
Small Calibers Seamless steel tubes for high(low and medium) pressure boilers and petrochemical industry
Standards:
ASME SA 179,
ASME SA 192
DINl7175 Deutsches industrial standard~
Application:
Used as the pipes on the heated side of low and medium pressure boilers(normally with operating pressure not higher than 5.88Mpa and
operating temperature below 450 oc);as the pipes on the heated sides of high·pressure boilers,economizers,overheaters,reheaters and pipes
for petrochemical industry(with the operating pressure above 9.8Mpa and operating temperature ranging between 450~C~650~C1
Diamensional tolerances:
| Types of steel tubes | Outer diameters | Wall thickness | ||
| Cold-rolled tubes | Tube sizes(mm) | Tolerances(mm) | Tube sizes (mm) | Tolerances(mm) |
| >30~50 | ±0.3 | >3~20 | ±10% | |
Mechanical properties:
| Standard codes | Models of steel tubes | Tensite strength(MPa) | Yield strength(MPa) | Elongation(%) | Hardness |
| GB3087 | 10 | 335~475 | ≥195 | ≥24 | / |
| 20 | 410~550 | ≥245 | ≥20 | / | |
| GB5310 | 20G | 410~550 | ≥245 | ≥24 | / |
| 20MnG | ≥415 | ≥240 | ≥22 | / | |
| 25MnG | ≥485 | ≥275 | ≥20 | / | |
| 15CrMoG | 440~640 | ≥235 | ≥21 | / | |
| 12Cr2MoG | 450~600 | ≥280 | ≥20 | / | |
| 12Cr1MoVG | 470~640 | ≥255 | ≥21 | / | |
| 12Cr2MoWVTiB | 540~735 | ≥345 | ≥18 | / | |
| 10Cr9Mo1VNb | ≥585 | ≥415 | ≥20 | / | |
| ASME SA210 | SA210A-1 | ≥415 | ≥255 | ≥30 | ≤143HB |
| SA210C | ≥485 | ≥275 | ≥30 | ≤179HB | |
| ASME SA213 | SA213 T11 | ≥415 | ≥205 | ≥30 | ≤163HB |
| SA213 T12 | ≥415 | ≥220 | ≥30 | ≤163HB | |
| SA213 T22 | ≥415 | ≥205 | ≥30 | ≤163HB | |
| SA213 T23 | ≥510 | ≥400 | ≥20 | ≤220HB | |
| SA213 T91 | ≥585 | ≥415 | ≥20 | ≤250HB | |
| SA213 T92 | ≥620 | ≥440 | ≥20 | ≤250HB | |
| DIN17175 | ST45.8/III | 410~530 | ≥255 | ≥21 | / |
| 15Mo3 | 450~600 | ≥270 | ≥22 | / | |
| 13CrMo44 | 440~590 | ≥290 | ≥22 | / | |
| 10CrMo910 | 480~630 | ≥280 | ≥20 | / |
Chemical composition:
| Standard codes | Models of steel tubes | Chemical compositions(%) | ||||||||||||||
| C | Si | Mn | P | S | Cr | Mo | Cu | Ni | V | Al | W | Ti | Nb | N | ||
| GB3087 | 10 | 0.07~0.13 | 0.17~0.37 | 0.38~0.65 | ≤0.030 | ≤0.030 | 0.3~0.65 | / | ≤0.25 | ≤0.30 | / | / | ||||
| 20 | 0.17~0.23 | 0.17~0.37 | 0.38~0.65 | ≤0.030 | ≤0.030 | 0.3~0.65 | / | ≤0.25 | ≤0.30 | / | / | |||||
| GB5310 | 20G | 0.17~0.24 | 0.17~0.37 | 0.35~0.65 | ≤0.030 | ≤0.030 | ≤0.25 | ≤0.15 | ≤0.20 | ≤0.25 | ≤0.08 | |||||
| 20MnG | 0.17~0.24 | 0.17~0.37 | 0.70~1.00 | ≤0.030 | ≤0.030 | ≤0.25 | ≤0.15 | ≤0.20 | ≤0.25 | ≤0.08 | ||||||
| 25MnG | 0.18~0.24 | 0.17~0.37 | 0.80~1.10 | ≤0.030 | ≤0.030 | ≤0.25 | ≤0.15 | ≤0.20 | ≤0.25 | ≤0.08 | ||||||
| 15CrMo | 0.12~0.18 | 0.17~0.37 | 0.40~0.70 | ≤0.030 | ≤0.030 | 0.80~1.10 | 0.40~0.55 | ≤0.20 | ≤0.30 | |||||||
| 12Cr2MoG | 0.08~0.15 | ≤0.50 | 0.40~0.70 | ≤0.030 | ≤0.030 | 2.00~2.50 | 0.90~1.20 | ≤0.20 | ≤0.30 | |||||||
| 12Cr1MoV | 0.08~0.15 | 0.17~0.37 | 0.40~0.70 | ≤0.030 | ≤0.030 | 0.90~1.20 | 0.25~0.35 | ≤0.20 | ≤0.30 | 0.15~0.30 | ||||||
| 12Cr2MoWVTiB | 0.08~0.15 | 0.45~0.75 | 0.45~0.65 | ≤0.030 | ≤0.030 | 1.60~2.10 | 0.50~0.65 | ≤0.20 | ≤0.30 | 0.28~0.42 | 0.30~0.55 | 0.08~0.15 | B 0.002~0.008 | |||
| 10Cr9Mo1VNb | 0.08~0.12 | 0.20~0.50 | 0.30~0.60 | ≤0.020 | ≤0.010 | 8.00~9.50 | 0.85~1.05 | ≤0.20 | ≤0.40 | 0.18~0.25 | ≤0.015 | 0.06~0.10 | 0.03~0.07 | |||
| ASME SA210 | SA210A-1 | 0.13~0.19 | ≥0.1 | 0.45~0.65 | ≤0.030 | ≤0.030 | ||||||||||
| SA210C | 0.18~0.24 | ≥0.1 | 0.80~1.10 | ≤0.030 | ≤0.030 | |||||||||||
| ASME SA213 | SA213 T11 | 0.05~0.15 | 0.50~1.0 | 0.30~0.60 | ≤0.030 | ≤0.030 | 1.00~1.50 | 0.50~1.00 | ||||||||
| SA213 T12 | 0.05~0.15 | ≤0.50 | 0.30~0.61 | ≤0.030 | ≤0.030 | 0.80~1.25 | 0.44~0.65 | |||||||||
| SA213 T22 | 0.05~0.15 | ≤0.50 | 0.30~0.60 | ≤0.030 | ≤0.010 | 1.90~2.60 | 0.87~1.13 | |||||||||
| SA213 T23 | 0.04~0.10 | ≤0.50 | 0.10~0.60 | ≤0.030 | ≤0.030 | 1.90~2.60 | 0.05~0.30 | ≤0.030 | 1.45~1.75 | B0.0005~0.006 | 0.02~0.08 | ≤0.040 | ||||
| SA213 T91 | 0.08~0.12 | 0.20~0.50 | 0.30~0.60 | ≤0.020 | ≤0.010 | 8.00~9.50 | 0.85~1.05 | ≤0.40 | 0.18~0.25 | ≤0.015 | 0.06~0.10 | 0.03~0.07 | ||||
| SA213 T92 | 0.07~0.13 | ≤0.50 | 0.30~0.60 | ≤0.020 | ≤0.010 | 8.50~9.50 | 0.30~0.60 | ≤0.40 | 0.15~0.25 | ≤0.015 | 1.50~2.00 | B 0.001~0.006 | 0.04~0.09 | 0.03~0.07 | ||
| DIN 17175 | ST45.8/III | ≤0.21 | 0.10~0.35 | 0.40~1.20 | ≤0.040 | ≤0.040 | ||||||||||
| 15Mo3 | 0.12~0.20 | 0.10~0.35 | 0.40~0.80 | ≤0.035 | ≤0.035 | 0.25~0.35 | ||||||||||
| 13CrMo44 | 0.10~0.18 | 0.10~0.35 | 0.40~0.70 | ≤0.035 | ≤0.035 | 0.70~1.10 | 0.45~0.65 | |||||||||
| 10CrMo910 | ||||||||||||||||
