Audited Supplier
a Lifetime
Electric
New
CE
12 Months
Single-Screw
Single Screw
Casting Film
Optical Acquisition System
Film Casting Die
30mm
25:1
320 X 250X170mm
Hapro
Plywood Sea
China
9024800000
Product Description
Around the package molding soft joint preparation methods, and extrusion molding method supplement each other, used in high pressure system for submarine cable soft joint, is very effective, especially when troubleshooting, winding and molding method is more convenient and effective In addition, foreign newspaper, below 138 kv cable joint, tend to use all around the package molding technology, for domestic under 110 kv
It makes more sense to system application Insulation and shield around the bag with the preparation of system development based on the integration of polymer extrusion flow delay cutting technology, equipped with electronic camera insulation insulation with real-time detection system with impurities preparation system composition: zero defect single-screw extruder stretch film cast mould cutting machine electronic camera type measuring instrument of impurities Dual channel independent mould machine.
1, Single screw extrusion system
2, Casting film forming multiple cutting system,, optical detection system
It makes more sense to system application Insulation and shield around the bag with the preparation of system development based on the integration of polymer extrusion flow delay cutting technology, equipped with electronic camera insulation insulation with real-time detection system with impurities preparation system composition: zero defect single-screw extruder stretch film cast mould cutting machine electronic camera type measuring instrument of impurities Dual channel independent mould machine.
1, Single screw extrusion system
| Photograph | Performance Index | Performance Parameter |
| Control interface | HMI | |
| Motor | AC inverter | |
| Motor power | 1.5 kW | |
| Reducer | TCG | |
| Speed ratio | 1:15 | |
| Screw speed | 100 r/min | |
| Screw Diameter | 20mm | |
| Screw L:D | 25 :1 | |
| Compression Ratio | 2.4:1or 3.6:1 | |
| Speed Range | 1-100 rpm | |
| Heating | Electrical Heating,PID,4 Zones | |
| Temp control system | RKC from Japan | |
| Heating zone | 4 Zones | |
| Max. Temperature | 350ºC | |
| Heating power | 3 kW | |
| Temperature sensor | J type thermocouple | |
| Cooling | Compressed Air cooling | |
| Pressure Accuracy | 0.5%F.S | |
| Pressure Range | 0.1 ~ 100 Mpa | |
| Output | 1 -5 kg/ hr | |
| Feeding speed | Manual adjustment | |
| Feeding | Screw metering feed | |
| Power supply | 3×380V,50/60 Hz ,+N +PE | |
| Dimension(L×W×H) | 1000×400×350 mm | |
| Weight | 150 kg | |
| Dies head (Select two from four) | Capillary Die (InnerФ1.0,Ф1.27,Ф2.0 L:D:20/1,30/1,40/1) | |
| Flat Die( L×W:60×1.5 mm, 0.8 kW) | ||
| Pipe Die(Inner Ф10, Outer Ф12.5) | ||
| Coating Wire Die (Core Ф1.5,Die outlet Ф4.0) |
2, Casting film forming multiple cutting system,, optical detection system
| Optical system | ||||||
| Camera brand | Nikon NIKKOR LENS | Camera lens parameters | AF Micro-Nikon 60mm f/2.8D | |||
| Capture card | Bitflow from USA | Sync Modes | Free-run, External Trig or Sync Modes | |||
| Resolution | 7450 ×1 Valid Pixels | Trig/Sync Input | CC1 | |||
| Pixel Size | 4.7×4.7 (μm×μm) | Integration Time | 16bit via Camera Link Serial | |||
| MAX. Date Rate | 60 MHz | Gain & Offset | Programmable via Camera Link Serial | |||
| MAX. Line Rate | 7.8 KHz | Gain Range | 0V/V to 16V/V (MAX. 24dB), 10bit Resolution | |||
| Spectral Response | 300nm~1000nm Typical | Data Format | 8bit / 10bit / 12bit Configurable | |||
| DR for Sensor | 65 dB | Output Format | 1Tap Camera Link Base | |||
| Measuring system | ||||||
| Measurement thickness | 0.04~2 mm | Resolution | 20μm | |||
| Field width | Calendaring 0~50 mm Casting 0~100 mm | Detection rates | 100% | |||
| Speed of Measurement | >1Kg/h | Accuracy | 1.0%F.S | |||
| Indoor environment | Class of ten thousand | Power supply | 3∮ AC 380V | |||
| Operating temperature | 0 ~ +40ºC | Rewinding film speed | 0~110mm/s | |||
| Environment humidity | < 65% | Roller cooling | Water | |||
| Film-forming methods | Calendaring or Casting | |||||
| Calendaring roller diameter | 110mm | Casting roller diameter | 200mm | |||
| Calendaring roller distance | 0~2.5mm | Center height of casting roller | 1 m | |||
| Flat die | 60mm*1.5mm customizable ,0.8kW | Film casting | 150mm*0.02~2.5mm Thickness adjustable | |||
| Film width of calendaring | < 60 mm | Film width of casting | < 120 mm | |||
| Film thickness of calendaring | 0.1mm~1.2mm | Film thickness of casting | 0.02~0.5mm | |||
| Rewinding control | Constant tension | Cutting-edge device for Casting | ||||
| Dimension (L×W×H) | 1600×750×1700mm | Weight | 500 kg | |||
