Swipe or use the arrows to view product images.
Electric Horizontal Single Suction Multistage Centrifugal Water Pump Manufacturer
| Price | $20000.00 |
|---|---|
| Min Order | 1 Piece |
| Availability | In Stock |
| Shipping From | Hunan, China |
| Popularity | 353 people viewed |
Model NO.:
D120-50X4
Max.Head:
>150m
Max.Capacity:
>400 L/min
Driving Type:
Motor
Impeller Number:
Multistage Pump
Working Pressure:
Low Pressure Pump
Influent Type of Impeller:
Single Suction Pump
Position of Pump Shaft:
Horizontal Pump
Pump Casing Combined:
Horizontal Split Pumps
Mounting Height:
Since Irrigation Centrifugal Pumps
Impeller:
Closed
Usage:
Pump, Pumps
Merge:
Changsha Swan
Merge2:
Wuxi Pump Works
Inlet Working Pressure:
Below 0.6MPa
Working Temperature:
0-80 Celsius
OEM/ODM:
Accept
Trademark:
LEO
Transport Package:
Export Plywood Case
Origin:
China
HS Code:
8413709990
Product Description
Introduction
D type pumps are single suction multistage segmental centrifugal pumps which adopt energy efficient hydraulic model,with wide performance range,high efficiency,reasonable structure,safe and steady operation,low noise,long life performance and easy installation and maintenance.
Application
D type pump apply to mining,factory and city water supply and drain,and are used for transporting clear water without solid particles, abrader and suspended substance or other liquids that their physical and chemical properties are similar to clear water
Performance Parameters Table
Product Attribute
Structural characteristics
The pump series is installed horizontally,the inlet is horizontal and the outlet is upward,they can be changed as required.the pump consists of pump body,rotor,balanced construction,bearing and seal
Pump body:suction casing,stage casing,discharge casing and diffuser are linked by bolts to form a working house
Rotor:it consists of shaft,impeller,shaft sleeve,balance disk etc,the spare parts of shaft are rolled into one by straight supported by bearing at both ends keys and sleeve nuts,the rotor is in pump casing
Balanced construction:it consists of gimbals,balancing sleeve,balanced pipeline
Parts of bearing:they consist of shaft box,bearing and bearing cover.except 600-80,800-80 type pump adopt sliding bearing and oil lubrication,other pumps adopt rolling bearing and grease lubrication
Sealing parts usually adopt packing seal,mechanical seal as well
Drive: pump is driven directly by motor through flexible coupling,viewed from the motor end, the rotating direction of pump is clockwise.
Ordering instructions
The necessary parameters: Pump type or capacity, head at required operating point,suction pressure,density,temperature,viscosity and causticity of pumped medium etc,type of shaft sealing,motor power,voltage,insulation class,level of protection,cooling system.
FAQ
D type pumps are single suction multistage segmental centrifugal pumps which adopt energy efficient hydraulic model,with wide performance range,high efficiency,reasonable structure,safe and steady operation,low noise,long life performance and easy installation and maintenance.
Application
D type pump apply to mining,factory and city water supply and drain,and are used for transporting clear water without solid particles, abrader and suspended substance or other liquids that their physical and chemical properties are similar to clear water
Performance Parameters Table
| Model | Flow(m³/h) | Head(m) | Pump efficiency(%) | Shaft power (kW) | Speed(rpm) | Impeller outer diameter(mm) | Stage |
| D120-50X4 | 120 | 200 | 73.3 | 89.22 | 2950 | 213 | 4 |
Product Attribute
| Attribute | Attribute | Attribute value |
| Performance | Speed | 2950 |
| Material | Impeller | HT250 |
| Pump shaft | 40Cr | |
| Bearing | SKF | |
| Pump casing | HT250 | |
| Working conditions | Medium temperatur(ºC) | Below 80ºC |
| Installation | Inlet diameter(mm) | DN125 |
| Outlet diameter(mm) | DN125 | |
| Direction of rotation | Clockwise | |
| Entrance orientation | Side entry | |
| Exit orientation | Vertical up | |
| Instructions | Low pressure male bottom | |
| Motor | Number of motor phases | 3 |
| Protection class | IP54 | |
| Insulation class | F | |
| Motor Power(kW) | 110 | |
| Motor model | YE3-315S-2 | |
| Power frequency(Hz) | 50 | |
| Rated voltage(V) | 380 | |
| Seal | Sealed form | Machinery Seal |
Structural characteristics
The pump series is installed horizontally,the inlet is horizontal and the outlet is upward,they can be changed as required.the pump consists of pump body,rotor,balanced construction,bearing and seal
Pump body:suction casing,stage casing,discharge casing and diffuser are linked by bolts to form a working house
Rotor:it consists of shaft,impeller,shaft sleeve,balance disk etc,the spare parts of shaft are rolled into one by straight supported by bearing at both ends keys and sleeve nuts,the rotor is in pump casing
Balanced construction:it consists of gimbals,balancing sleeve,balanced pipeline
Parts of bearing:they consist of shaft box,bearing and bearing cover.except 600-80,800-80 type pump adopt sliding bearing and oil lubrication,other pumps adopt rolling bearing and grease lubrication
Sealing parts usually adopt packing seal,mechanical seal as well
Drive: pump is driven directly by motor through flexible coupling,viewed from the motor end, the rotating direction of pump is clockwise.
Ordering instructions
The necessary parameters: Pump type or capacity, head at required operating point,suction pressure,density,temperature,viscosity and causticity of pumped medium etc,type of shaft sealing,motor power,voltage,insulation class,level of protection,cooling system.
FAQ
| 1. Q:Are you a manufacturer or trading company |
| A:We are a manufacturer that specializes in industrial pump for 60 years |
| 2. Q:What payment term do you prefer? |
| A:Normally we take payment term 30% T/T in advance,70% paid before shipment, we can also accept L/C at sight. |
| 3. Q:What about the package? |
| A:Standard export plywood case |
| 4. Q:How long is the warranty? |
| A: Eighteen (18) months after delivery, twelve (12) Months from the date of commissioning, whichever comes earlier |
| 5. Q:Is it acceptable to make customer's own brand? |
| A: Sure, we can do OEM & ODM |
| 6. Q:How many days does it take for manufacturing? |
| A: It depends on order quantity and pump types. Normally it takes 20-120 days |
- Similar Products
$10000.00
1 Piece (MOQ)
Mud Gravel Mining Slurry Ash Sewage Sand Heavy Duty Trash Pump
Tinda Pump Co. Ltd.
$30000.00
1 Piece (MOQ)
ANSI/ASTM Centrifugal Caustic Soda Circulating Chemical Pump
Sichuan Zigong Industrial Pump Co., Ltd.
$14000.00
1 Piece (MOQ)
Versatile Cdl Pump for High Pressure Water Supply Solutions
Suzhou South Pump Pump Industry Co., Ltd