Audited Supplier
C-550
Instant Adhesive
Solid-State
Construction, Aluminium-Plastic Panel
Silicone
Room Curing
Rubber
Waterproof
Curing Agent
Organic Material
Clear
340g
280g
60g
24 PCS/CTN
30*20*24cm
10-30 Mins
4 Days
After 21 Day
1.45
CSJ
Carton
300ml
China
3506100090
Product Description
High Grade Neutral Silicone Sealant For Aluminum Doors and Windows (C-550)
Characteristics:
1.One component
2. Neutral Curing and non-corrosive to metal, coated glass, concrete and marble
3. Non-discoloring.
4. Excellent adhesion to glass, metal and plastic etc
5. Excellent resistance to low and high temperature, little performance changes between -40 ºC~150 ºC
6. Excellent resistance ultraviolet radiation
7. Odorless
Application:
For a wide range of Aluminum doors and windows, plastic steel doors and windows, stainless steel, glass, Aluminum sheet, ceramics, sky light, roof, most of building material. Can not use for coated glass.
Limitations:
1.Cannot be used as structural sealant.
2.Not compatible with materials with grease or exudation.
3.The construction surface should be clean and dry.
4.Not applicable to the seal of the immersed, airtight, or comprising substrates like copper, brass and lead, and oil-exudation surfaces.
5.Cannot be used on the substrate surface below 6ºC or above 40 ºC
Curing Time:
Track-free Time is between 15 to 20 minutes at room temperature
Completely curing Time is between 48 hours to 96 hours at room temperature.
Way of use:
1.preparation:clean,de-grease and dry the surface.protect the edges of sealing gap with masking tape;
2.cut the nozzle according to the fissure width,cut off the tube outlet over the thread and screw the nozzle on;
3.application temperature +5c to +30c;
4.extrude silicone by means of cartridge gun;
5.tool the sealant with a wet spatula before formation occurs;
6.up to 15min, remove the masking tape;
7.fresh spots can be clean with water, after hardening mechanically only
Notices:
1. For best result, use opened cartridges on the same day. Otherwise store it strictly tightened
2. Pre-test is necessary to ensure the excellent adhesive property.
3. Avoid contacting with skin or eyes, in case of contacted, rinse immediately with plenty of water, go to hospital if necessary
4. Keep away from children before curing.
5. Avoid contaminating food, medicine or cosmetics.
Color available:
White, grey, black, others of special order
Packaging
Cartridge: 300ml 24 cartridges/carton
Gross weight: 470g Net weight: 410g
Storage and transportation:
1. 12 months stored in a dry and ventilated place below 27ºc in original packaging.
2. non-dangerous, can be transported by train, automobile, ship.
3. Uncured product may irritate eyes. In case of eyes contact, rinse them immediately with water and seek medical aid.
4. Keep out of reach of children.
Testing Standard: GB/T 14683-2003
TECHNICAL DATA SHEET
Certificate
Office Building
FAQ:
1.Can u send sample to us ?
Yes, the sample is free.
2.Can you give us private design ?
Yes, we offer OEM service, can making your own brand.
3.What's your guarantee?
10-15 years.
4.Can you provide us with your client information ?
Yes, for checking our company reputation and sample collection.
5.How many days to produce one 20'container?
5-10days.
6.Can we visit factory?
Yes, warmly welcome to visit us at any time.
7.What are the documents we provide ?
Packing list, commercial invoice, CO / FORM E / FORM A , BL making according to your demand.
Characteristics:
1.One component
2. Neutral Curing and non-corrosive to metal, coated glass, concrete and marble
3. Non-discoloring.
4. Excellent adhesion to glass, metal and plastic etc
5. Excellent resistance to low and high temperature, little performance changes between -40 ºC~150 ºC
6. Excellent resistance ultraviolet radiation
7. Odorless
Application:
For a wide range of Aluminum doors and windows, plastic steel doors and windows, stainless steel, glass, Aluminum sheet, ceramics, sky light, roof, most of building material. Can not use for coated glass.
Limitations:
1.Cannot be used as structural sealant.
2.Not compatible with materials with grease or exudation.
3.The construction surface should be clean and dry.
4.Not applicable to the seal of the immersed, airtight, or comprising substrates like copper, brass and lead, and oil-exudation surfaces.
5.Cannot be used on the substrate surface below 6ºC or above 40 ºC
Curing Time:
Track-free Time is between 15 to 20 minutes at room temperature
Completely curing Time is between 48 hours to 96 hours at room temperature.
Way of use:
1.preparation:clean,de-grease and dry the surface.protect the edges of sealing gap with masking tape;
2.cut the nozzle according to the fissure width,cut off the tube outlet over the thread and screw the nozzle on;
3.application temperature +5c to +30c;
4.extrude silicone by means of cartridge gun;
5.tool the sealant with a wet spatula before formation occurs;
6.up to 15min, remove the masking tape;
7.fresh spots can be clean with water, after hardening mechanically only
Notices:
1. For best result, use opened cartridges on the same day. Otherwise store it strictly tightened
2. Pre-test is necessary to ensure the excellent adhesive property.
3. Avoid contacting with skin or eyes, in case of contacted, rinse immediately with plenty of water, go to hospital if necessary
4. Keep away from children before curing.
5. Avoid contaminating food, medicine or cosmetics.
Color available:
White, grey, black, others of special order
Packaging
Cartridge: 300ml 24 cartridges/carton
Gross weight: 470g Net weight: 410g
Storage and transportation:
1. 12 months stored in a dry and ventilated place below 27ºc in original packaging.
2. non-dangerous, can be transported by train, automobile, ship.
3. Uncured product may irritate eyes. In case of eyes contact, rinse them immediately with water and seek medical aid.
4. Keep out of reach of children.
Testing Standard: GB/T 14683-2003
TECHNICAL DATA SHEET
| No | Item | The standard | Test result | ||
| 1 | Appearance | Have no grain, no agglomerations, no skinning, and no bubble. | Pass the standard | ||
| 2 | Density (g/cm3) | ±0.1 | 1.438 | ||
| 3 | Droop degree mm | Uprightness | ≤3 | 0 | |
| Level | No damage | No damage | |||
| 4 | Skinning time(h) | ≤3 | 0.33 | ||
| 5 | Elastic recovery ratio (%) | ≥80 | 92 | ||
| 6 | Extrusion ability(ml/min) | ≥80 | 116 | ||
| 7 | Tensile modulus (Mpa) | 23ºC | ≤ 0.6 | 0.7 | |
| 8 | Cold-hot adhesive | No damage | No damage | ||
| 9 | Under water adhesive | No damage | No damage | ||
| 10 | UV radiation | No damage | No damage | ||
| 11 | Definite Elongation | No damage | No damage | ||
Certificate
Office Building
FAQ:
1.Can u send sample to us ?
Yes, the sample is free.
2.Can you give us private design ?
Yes, we offer OEM service, can making your own brand.
3.What's your guarantee?
10-15 years.
4.Can you provide us with your client information ?
Yes, for checking our company reputation and sample collection.
5.How many days to produce one 20'container?
5-10days.
6.Can we visit factory?
Yes, warmly welcome to visit us at any time.
7.What are the documents we provide ?
Packing list, commercial invoice, CO / FORM E / FORM A , BL making according to your demand.
