Audited Supplier
Charging Indicator Light
1. Solid Green LED = Battery full Charged
2. Flashing Green or Yellow or Red = Battery charging
3. Battery Level Display:
Green LED = High Volt ( >11.5V ),
Yellow LED = Medium Volt (11.5-10.5V),
Red LED = Low Volt (<10.5V).
Please Note:The indicator will flash when charging, and when fully charged, it will display green.
·On/Off Switch - Will turn the Batten Light On and Off Manually. When using the remote control and the PIR Module, it must always be on.
Using Remote Control
1. Solar Batten (Tri-Proof) Light 30W Tube with 2.4G Remote Control is an advanced commercial-grade energy-efficient lighting system powered bySolar Energy and battery.
2. The range between the light and Remote control can be up to 100m.
3. One Remote Control can be linked to up to Four Groups Batten Lights, Each Group can up to 256 Lights.
4. Batten Lights can be combined into a lighting system with up to FOUR Groups link to one Remote Control and operated via a single
Remote Control Pad.
5. Bright Powerful 30W lighting supplied by 120 LED SMT2835 with adjustable brightness 8% to 100% via the Remote Controller.It can last for
50 hours at 8% brightness
6. Extended and Improved 18V 30W Solar Panel with High Energy Conversion rate to charge full the battery in 5-6h in sunny weather conditions.
7. Detached Solar Panel design with 3m extension cord allows keeping the panel outdoor at the direct sunlight while the light can be used at
shaded locations or indoor.
8. The light can be operated with Remote pad or manually switch. Press and Hold the Dimmer+/Dimmer-. All lights can be dimmed together.
9. Suitable for outdoor and indoor use including daytime operation.
10.Durable Body made of Aluminium combined with industrial-grade pc. enhanced heatproof and weather resistance.
11.Easy to install, setup and operate. Completely safe. Charging protection and discharging protection.
12. No maintenance cost. User-friendly design, no wiring or any professional installation needed.
Using the independent remote sensor module
1. One Remote Sensor Module can control all lights linked to the remote control.
2. The detection distance of this sensor is 8-10 meters.And it can be set a delay time(Time Knob) and adjusted ambient brightness
(LUX Knob). See the PIR PAD diagram.
3. When the Remote Sensor Module detects human signal, it will simultaneously emit a 2.4G remote control signal to turn on all lights linked to
the remote control. And when the preset time ends, it will simultaneously turn off all lights.
4.Even if the remote control turns off all lights, the Remote Sensor Module will still turn on all lights when someone enters the detection area.
5. The Remote Sensor Module has a manual switch that can be turned off when not needed.
Syncing the Remote Control to the Light and the PIR Module
Before using the remote control for the first time, you will need setup the remote control.
control, then turn on the power switch of the light.
control is already linked to the light.
conterol , then turn on the power switch of the PIR Module.
When the Green Indicate LED of the PIR Module flashes
3 times ,Indicates that the remote control is already linked
to the PIR Module.
LUX Dial: Adjusts the level of darkness at Dusk that must be reached before the light turns on.
TIME Dial: Adjust delay time from 5 seconds to 5 minutes.
SENS Dial: Adjust the sensitivity from min. to max. (about 0-12 meters).
Product Details:
FAQ
1.Q: Are you a factory or a trading company?
A: We are a manufacturer. Welcome OEM and ODM for you.
2. Can we have a sample order?
A: Of course! Any sample order is welcome for testing and checking.
3.What is the warranty for the products?
A: Battery:3 years. Controller/LED:5 years. solar panels:15-20 years
4.How to ship the goods?
A: By sea usually. If urgent requirement, air-shipping is available(except:Batteries)
5. How to deal with the fault?
A: If the problem caused by manufacturing quality, we will change and replace it in free.
